Yaskawa E7 Drive User Manual - Manual (Page 235)

Index - 3
E
EEPROM............................................. 6-2, 6-12, 6-14, D-12
Elapsed Timer
Monitor............................................... 3-9 to 3-11, A-27
Parameters ................... 5-55, A-24, A-25, A-27 to A-29
Electrical Installation........................................................ 2-1
EMC ................................................................................. F-1
Enclosed wall-mounted ..................................1-5 to 1-9, C-4
Enclosure Style (type) .......................................1-2, 1-4, C-4
Energy Saving
Parameters ........................................................ A-7, B-3
Selection.................................................................. 5-24
Environment ...........................................1-13, 6-18, 7-3, C-4
ESC Key ........................................................................... 3-3
External Faults (EF) .............................. 2-14, 6-4, 6-9, A-14
F
Factory Repair ..........................................Inside Back Cover
Fan, Heatsink Cooling
Checking ................................................................. 6-24
Cumulative Operation Time Setting ...................... A-25
Fuse, Checking........................................................ 6-24
Inspecting ..........................................................7-2, 7-3
Operation Delay Time................................... 5-49, A-22
Operation Selection....................................... 5-49, A-22
Replacement Method .........................................7-4, 7-5
Troubleshooting ...................................................... 6-10
Fast-Stop Time ...................................5-25, A-7, A-13, A-14
Faults
Clearing ........................................................... 3-3, A-25
Covered by Auto Restart......................................... 5-45
Detection ................................................................... 6-2
Digital Output Signal ..................................... 2-14, A15
Effect on Auto Restart............................................. 5-45
History........................................................... 3-11, A-29
Listing of ................................................................... 6-2
Reset......................................................3-3, A-13, A-21
Trace.............................................................. 3-10, A-28
Feedback (PI Function) .......................................... 5-15, A-5
Differential .................................................... 5-36, A-16
Loss Detection................................................. 5-18, A-6
Square Root Function Activation.................... 5-23, A-6
Field Service.............................................Inside Back Cover
Field Wiring.............................................................2-3, 2-12
FLA, Motor .................................4-6, 5-31, 6-13, A-11, B-3
Flash ID ........................................................................ A-27
Floating Point (Up/Down) Control ...................... 6-14, A-12
Forward Run/Stop Command................................2-14, 2-18
Programming..............................................5-4, 5-5, A-4
Frequency Detection...................................................... A-15
Frequency, Output
Accuracy ...................................................................C-4
Command Selection .................................................. 5-4
Jump..............................................5-27, 6-19, 6-20, A-9
Lower Limit.....................................................5-26, A-9
Max. Output...........................................5-29, A-10, C-2
Meter (Analog Monitor) .........................................A-17
Mid Output .............................................................A-10
Minimum Output ...........................................6-16, A-10
Monitor (U1-02) .....................................................A-26
Prohibited......................................5-27, 6-19, 6-20, A-9
Rated......................................................................... C-2
Setting Resolution..................................................... C-4
Setting Signal (Speed Command)............................. C-4
Troubleshooting ............................................. 5-27, 6-20
Upper Limit ........................................... 5-26, 6-20, A-9
Frequency Reference (speed command)
Analog Input ................................ 2-12, 2-18, A-4, A-16
Bias ................................................... 5-33 to 5-38, A-16
Gain .................................................. 5-33 to 5-38, A-16
Loss Detection ...............................................5-43, A-21
Lower Limit.....................................................5-26, A-9
Preset References 1 to 4............................................A-8
Terminals .............................................. 2-12, 2-14, 2-18
Upper Limit ........................................... 5-26, 6-20, A-9
Setting Method Selection (MOP) ..................5-54, A-24
Source (b1-01) ........................................... 3-6, 5-4, A-4
Full Load Amps (FLA) ................ 4-6, 5-31, 6-13, A-11, B-3
Fuse Blown Protection........................ 6-7, 6-22 to 6-24, C-4
FWD Indicator ..................................................................3-5
G
Gain Adjustments ....................................... 5-33, 5-38, A-16
Gate Drive PCBs
Inspecting...................................................................7-2
Ground Fault Function.................................. 5-45, 6-4, A-22
Ground Fault Interrupter (GFI)
Troubleshooting .......................................................6-19
Grounding ..........................................2-11 to 2-14, 4-3, 6-18
Protection.................................................................. C-4
Shield Wire .................................................... 2-12, 2-18
Terminals ..........................................1-5, 1-6, 2-2 to 2-8
H
Hand
Frequency Reference Selection .............. 5-3, A-4, A-27
Indicators ........................................................... 3-5, 3-6
HAND Key ................................................................3-4
Function Selection ...........................................A-25
Mode................................................................ 3-4, 5-37
Troubleshooting .......................................................6-16
Hardware Protection Parameters ..........................5-48, A-22
Harmonics, Mitigation ............................................. C-2, C-3
Heat Loss Data.......................................................1-11, 1-14
Heatsink Fan ................................................. 5-49, 7-2, A-25
Hex, converting to decimal............................................A-30
TM_E7_01_07182008.book Page 3 Wednesday, July 23, 2008 2:35 PM