Yaskawa E7 Drive User Manual - Manual (Page 238)

Index - 6
P
Parameters
Accel/Decel (C1-01 - C1-11) ................................... A-7
Analog Inputs (H3-02 - H3-13).............................. A-16
Analog Outputs (H4-01 - H4-08)................. A-17, A-18
Auto-Tuning (T1-02 - T1-04) ................................ A-25
Capacity Related .......................................................B-1
Carrier Freq (C6-02 - C6-05) ................................... A-8
Com OPT Setup (F6-01 - F6-05) ............................A-11
COPY Function (o3-01 - o3-02) ............................ A-25
DC Braking (b2-01 - b2-09)..................................... A-4
Delay timers (b4-01 - b4-02).................................... A-5
Digital Inputs (H1-01 - H1-05) ................. A-12 to A-14
Digital Outputs (H2-01 - H2-02)............................ A-15
Energy Saving (b8-01 - b8-06) ................................ A-7
Example of Changing.....................................3-15, 3-16
Factory Reset (Initialize).......................................... A-2
Fault Restart (L5-01 - L5-03)................................. A-21
Hdwe Protection (L8-01 - L8-19) .......................... A-22
High Slip Breaking (n3-01 - n3-04) ....................... A-23
Hunting Prevention (n1-01 - n1-02)....................... A-23
Initialization (A1-00 - A1-05).................................. A-2
Jump Frequencies (d3-01 - d3-04) ........................... A-9
Key Selections (o2-01 - o2-15) .................... A-24, A-25
Listing of ..................................................... A-1 to A-29
Modified...........................................................3-7, 3-14
Monitor Select (o1-01 - o1-08) .................... A-23, A-24
MOP/Trim Control (d4-01 - d4-02) ......................... A-9
Motor Overload (L1-01 - L1-05) ........................... A-19
Motor Setup (E2-01 - E2-05) ..................................A-11
PI Control (b5-01 - b5-30) ............................... A-5, A-6
Preset Reference (Speeds) (d1-01 - d1-17) .............. A-8
Programming (Basic) ....................................5-1 to 5-60
PwrLoss Ridethru (L2-01 - L2-05) ........................ A-19
Ref Detection (L4-01 - L4-06)............................... A-21
Reference Limits (d2-01 - d2-03) ............................ A-9
S-Curve Acc/Dec (C2-01 - C2-02) .......................... A-7
Sequence (b1-01 - b1-12)......................................... A-4
Serial Com Setup (H5-01 - H5-09) ........................ A-18
Setting and Reading ......................................3-7 to 3-16
Speed Search (b3-01 - b3-14) .................................. A-5
Stall Prevention (L3-01 - L3-06)............................ A-20
Torque Comp (C4-01 - C4-02)................................. A-8
Torque Detection (L6-01 - L6-03) ......................... A-21
Troubleshooting ...................................................... 6-15
User Limited Access (A2-01 - A2-32)............. A-2, A-3
V/f Pattern (E1-01 - E1-13).................................... A-10
Parity - See Modbus Communications........................... D-2
Parts
Ordering Replacement ......................Inside Back Cover
Password
Setting ...................................................................... A-2
Troubleshooting ...................................................... 6-15
PCB
Control
Inspecting ...........................................................7-2
Gate Drive
Inspecting ...........................................................7-2
Power
Inspecting ...........................................................7-2
Terminal
Inspecting ...........................................................7-2
Removing and Mounting....................................7-6
Peripheral Devices
AC and DC reactor ................................................... E-4
Magnetic Contactor .................................................. E-4
Molded-Case Circuit Breaker (MCCB).................... E-2
Noise filter ................................................................ E-4
Troubleshooting .......................................................6-18
Phase Loss Detection
Input.................................................................6-7, A-22
Phase-to-Phase Short ................................ 6-5, 6-7, 6-10
Physical Installation - See Installation, Physical ..............1-1
PI Function
Accel/Decel Time ............................................5-19, A-6
Block Diagram.........................................................5-15
Feedback............................ 5-15 to 5-18, 6-4, 6-10, A-6
Differential .............................................5-15, A-16
Loss Detection Level................................5-18, A-6
Loss Detection Time.................................5-18, A-6
Reference Missing Detection ...................5-18, A-5
Square Root Activation ............................5-23, A-6
Integral Limit Setting.......................................5-16, A-5
Integral Time Setting .......................................5-17, A-5
Maximum Boost Time.....................................5-22, A-6
Offset Adjustment............................................5-17, A-5
Output ..............................................................5-17, A-5
Gain Setting..............................................5-18, A-5
Level Selection .........................................5-17, A-5
Limit .........................................................5-17, A-5
Primary Delay Time Constant ..................5-17, A-5
Square Root Monitor ................................5-23, A-6
Parameters ..................................5-15 to 5-23, A-5, A-6
Proportional Gain (PI) ....................................5-14, A-5
Setpoint............................................................5-15, A-6
Boost Setting ............................................5-21, A-6
Display Scaling.........................................5-20, A-6
Selection ...................................................5-19, A-6
Value.........................................................5-20, A-6
Sleep
Delay Time ...............................................5-19, A-6
Function............................................................5-19
Function Start Level .................................5-19, A-6
Input Source .............................................5-21, A-6
Snooze
Deactivation Level ...................................5-21, A-6
Delay Time ...............................................5-21, A-6
Feedback Level.........................................5-22, A-6
TM_E7_01_07182008.book Page 6 Wednesday, July 23, 2008 2:35 PM