Yaskawa E7 Drive User Manual - Manual (Page 240)

Index - 8
Shunt Connector CN15 ........................................ 2-16, A-18
Sinking/Sourcing Mode.................................................. 2-17
Skip Frequency.................................... 5-27, 6-19, 6-20, A-9
Slave ................................................................................ D-2
Sleep Function........................................................ 5-19, A-6
Snooze Function ............................................5-21, 5-22, A-6
Soft Charge Contactor
Alarm....................................................................... 6-11
Checking ................................................................. 6-22
Fault........................................................................... 6-8
Soft Charge Resistor
Checking ................................................................. 6-22
Preventive Maintenance ............................................ 7-3
Soft CLA Selection ....................................................... A-22
Soft Start.......................................................................... A-7
Software Number (U1-14)............................................. A-27
SPEC .........................................................................1-3, 1-4
Specifications ...................................................................C-1
Design ............................................................. 1-4, A-25
General ......................................................................C-4
Standard Drive
208-240 VAC .....................................................C-2
480 VAC.............................................................C-3
Nameplate .......................................................... 1-3
Speed
Agreement ...........................................5-46, A-15, A-21
Control Accuracy ......................................................C-4
Range.........................................................................C-4
Speed Command - See Frequency Reference
0-10Vdc......................................... 2-12, 2-14, 2-18, 4-9
4-20mA ......................................... 2-12, 2-14, 2-18, 4-9
Limits .....................................................5-26, 6-20, A-9
Loss Detection............................................... 5-43, A-21
Selection............................................. 3-6, 4-6, 5-4, A-4
Setting Selection...................................................... 5-54
Signal Polarity..................................................2-12, 4-9
Troubleshooting .............................................6-16, 6-17
Speed Reference, Multiple ....................................................
(Multi-step Speed Operation)................................... A-8
Speed Search ................................................................. 5-11
Auto-Tuning ........................................................... 5-59
Parameters ................................................................ A-5
Stall Prevention
Parameters ..................................................... 5-40, A-20
Specifications ............................................................C-4
Troubleshooting ...................................................... 6-17
Start-up ...................................................................4-1 to 4-9
Assistance..........................................Inside Back Cover
Benchmark data......................................................... 4-8
Preparation for........................................................... 4-2
Procedure................................................................... 4-5
STOP Indicator..........................................................3-2, 3-6
Stopping Method ....................................... 4-7, 5-6, 5-7, A-4
Coast to Stop ............................................................. 5-5
Coast w/Timer ........................................................... 5-6
DcInj to Stop..............................................................5-7
External Fault from OPT Card................................ A-11
Modbus Communications.........................................D-4
Ramp to Stop .............................................................5-6
Selection (OH) ..............................................5-48, A-22
Storage Temperature ........................................................ C-4
Switching Frequency (Carrier Frequency) .....2-11, A-8, B-3
T
Technical Support .................................... Inside Back Cover
Technical Training ................................... Inside Back Cover
Temperature
Ambient Operating ..........................................1-13, C-4
Ambient, Setting.....................................................A-22
Effect on Frequency Accuracy ................................. C-4
Storage ...................................................................... C-4
Troubleshooting .......................................................6-18
Terminal PCB, Control
Inspecting...................................................................7-2
Removing and Mounting ...........................................7-6
Terminal A1 ......................................2-14, 2-18, 5-33, A-16
Terminal A2 ..............................2-14, 2-18, 5-35, 5-38, A-16
Terminal AM .................................... 2-14, 2-18, A-17, A-18
Terminal FM .................................... 2-14, 2-18, A-17, A-18
Terminal M1-M2 ........................................ 2-14, 2-18, A-15
Terminal M3-M4 ........................................ 2-14, 2-18, A-15
Terminal R+, R-, S+, S- ................................ 2-14, 2-18, D-3
Terminal S1, S2.......................................2-14, 2-18, 5-3, 5-5
Terminals S3 to S7 ........................2-14, 2-18, A-12 to A-14
Terminal
Arrangement ............................................... 1-5, 1-6, 2-2
Configuration.............................................................2-2
Connections .............................................................2-18
Control Circuit...................................... 2-12, 2-14, 2-18
Main Circuit ................................................... 2-3 to 2-8
Inspecting ...........................................................7-2
Wiring...................................................... 2-3 to 2-7
Screw Sizes..................................................... 2-3 to 2-7
Terminating Resistance...........................................2-15, D-3
Three-Wire Operation .......................................................5-5
Timers, Delay...................................................................A-5
Timers, Elapsed.....................................................5-55, A-25
Timer, On Delay........................................................5-9, A-4
Torque Compensation ......................................................A-8
Torque Detection
Faults .........................................................................6-6
Level .............................................................. 5-46, 5-47
Nuisance ..................................................................5-46
Parameters ..............................................................A-21
Selection ........................................................ 5-46, 5-47
Time............................................................... 5-46, 5-47
Torque Output .................................................................6-17
Transformers, Preventive Maintenance ............................7-3
TM_E7_01_07182008.book Page 8 Wednesday, July 23, 2008 2:35 PM