Yaskawa E7 Drive User Manual - Manual (Page 236)

Index - 4
High-Slip Braking ......................................................... A-23
H/O/A (Hand/Off/Auto) .........................................3-2 to 3-6
Horsepower, converting to kW....................................... 5-59
Humidity......................................................................... 1-13
Ambient Operating....................................................C-4
Hunting Prevention
Parameters .............................................................. A-23
Troubleshooting ...................................................... 6-19
I
IEC IP00 ............................................................1-2, 1-4, C-4
IEC IP20 ....................................................................1-2, 1-4
IGBT (Transistor Module)
Inspecting .................................................................. 7-2
Testing ..................................................................... 6-23
INCREASE Key......................................................3-3, 5-54
Troubleshooting ...................................................... 6-15
Indicators, Mode......................................... 3-2, 3-5, 3-6, 4-5
Initialization ............................................................ 5-1, A-2
Mode Selection.......................................................... 5-3
Parameters ...................................................... A-2, A-24
User ........................................................5-3, 5-54, A-24
Input
Diodes .....................................................6-21, 6-22, 7-2
Fuses ................................................ 2-9, 2-10, E-2, E-3
Multi-function Terminals
Analog Inputs...........................................................
.......... 2-12, 2-14, 2-18, 5-33, 5-38, A-4, A-9, A-16
Digital Inputs ...........................................................
...............2-12, 2-14, 2-18, 6-15, 6-19, A-12 to A14
Phase Loss Detection Level ............................ 6-7, A-22
Power............................................................... 2-18, C-2
Terminal Status (U1-10)......................................... A-26
Voltage.................................................... A-10, C-2, C-3
Setting .............................................4-5, 5-22, A-10
Inspection
Periodic ..................................................................... 7-2
Receiving................................................................... 1-3
Installation
Electrical ................................................................... 2-1
Physical ..................................................................... 1-1
Orientation & Clearances................................. 1-14
Site ........................................................... 1-11, C-4
Integral Control (PI) ....................................................... 5-16
Interference....................................................................... F-1
J
Jog Frequency Reference ................... 2-14, 2-18, A-8, A-12
Jump Frequency .................................. 5-27, 6-19, 6-20, A-9
K
Keypad .................................................................3-1 to 3-16
kVA .........................................................................1-11, C-2
Auto-Tuning ..................................................5-59, A-25
Error............................................................... 6-12, 6-14
Parameters Affected by............................................. B-3
Selection .................................................................A-24
kW, Converting from HP ................................................5-59
kWH User Monitor Initialization...................................A-25
L
Label, Control Terminals ..................................................2-2
Lamps, Indicator .........................................3-2, 3-5, 3-6, 4-5
Language Selection...................................................5-2, A-2
LCD Display ............................................................. 3-2, 3-8
LED (Indicators) .........................................3-2, 3-5, 3-6, 4-5
Lights ..........................................................3-2, 3-5, 3-6, 4-5
Line-borne Interference Interference ................................F-2
Line-to-Line Resistance, Motor..................................... A-11
LonWorks..............................................................iv, 5-4, 5-5
Loss of Load .........................................................5-46, A-21
M
Main Circuit
Configuration................................................... 2-9, 2-10
Terminals ............................... 1-5, 1-6, 2-2 to 2-8, 2-18
Test Procedure .........................................................6-21
Wire Sizes and Connectors ............................. 2-3 to 2-7
Wiring Diagrams......................................................2-18
Main Menu
Functions ...................................................................3-7
Structure........................................................ 3-8 to 3-14
Maintenance......................................................................7-1
Mass, Drive (Weight).................................... 1-3, 1-7 to 1-10
Master Frequency Reference Terminal Selection ..................
..............................................................................5-39, A-16
Master/Slave .......................................................D-2 to D-14
Mechanical Vibration...........................5-27, 6-19, 6-20, A-9
Mechanical Resonance ........................5-27, 6-19, 6-20, A-9
MENU Key ............................................................... 3-3, 3-7
Menu Trees, Digital Operator .............................. 3-8 to 3-14
Metasys ....................................................... iii, iv, A-18, D-1
Meters ............................................................................A-23
Modbus Communications ...................................D-1 to D-14
Baud Rate ........................................................6-9, A-18
Terminals ....................................................... 2-12, 2-14
Mode Selection ..................................................... 3-3 to 3-6
Model Number....................................................... 1-2 to 1-4
Modified Constants (Parameters) Menu ................. 3-7, 3-14
Molded Case Circuit Breaker (MCCB) ....................E-2, E-3
Momentary Power Loss Ride-thru.........................................
............................................ 5-11, 5-39, A-5, A-19, B-3, C-4
Monitor
Configuration...........................................................5-50
Parameter List....................................... 3-9, A-26, A-27
TM_E7_01_07182008.book Page 4 Wednesday, July 23, 2008 2:35 PM