Document Outline

• ArmorStart LT Distributed Motor Controller User Manual - DeviceNet
• Important User Information
• General Precautions
• Precautions for Bulletin 294D Applications
• Software Requirements
• Additional Resources
• Rockwell Automation Support
• Installation Assistance
• New Product Satisfaction Return
• Summary of Changes
  • New and Updated Information
• Preface
  • European Communities (EC) Directive Compliance
  • Low Voltage and EMC Directives
  • Introduction
• Table of Contents
• Chapter 1
  • Product Overview
    • Description
    • Features
    • Feature Description
      • Standard Features Across Product Family
      • DeviceNet Network Capabilities
    • Factory-Installed Options
    • ArmorStart LT Characteristics
    • Catalog Number Explanation
    • ArmorStart LT Characteristics
    • Catalog Number Explanation
    • Basic Operation
      • Group Motor Installations for USA and Canada Markets
      • Control Circuit
      • Motor Circuit
      • Local I/O
      • Overload Protection
    • Mode of Operation Bulletin 290D/291D
      • Full-Voltage Start
    • Mode of Operation Bulletin 294D
      • Sensorless Vector Performance
    • Status LEDs and Reset
      • Electronic Data Sheet (EDS)
    • Fault Diagnostics
      • Protection Faults
      • Protection Warnings
    • Optional HOA Selector Keypad
      • Keypad Local Control
    • Optional HOA Keypad Configuration (Bulletin 290D/291D only)
    • Optional HOA Selector Keypad with Jog Function (Bulletin 294D only)
      • Keypad Disable Parameter
    • Source Brake Contactor and Connector (Bulletin 294D only)
• Chapter 2
  • Installation and Wiring
    • Receiving
    • Unpacking
    • Inspecting
    • Storing
    • Installation Precautions
    • Precautions for Bulletin 290D/291D Applications
    • Precautions for Bulletin 294D Applications
    • Dimensions
    • Dimensions
    • Connection Locations
    • Wiring Terminal Detail
    • Branch Circuit Protection
    • Typical System Example
    • ArmorConnect Power Media
    • ArmorConnect Cable Ratings
      • Branch Circuit Protection Requirements for ArmorConnect Three-Phase Power Media
    • Electrical Wiring
    • Group Motor Installations for USA and Canada Markets
    • Wiring
      • Cable Workmanship Guidelines
      • Service Space
      • Hand Operation (HOA) Considerations
    • General Wiring Considerations
    • Grounding
      • Grounding Safety Grounds
      • Grounding PE or Ground
      • Grounding Motors
    • Power Distribution
      • Delta/Wye with Grounded Wye Neutral
    • AC Line Voltage
    • Line Reactor
    • Bulletin 294D Motor Cable Considerations
      • Unshielded Cable
      • Shielded Cable
      • Recommended Cable Connectors/Glands
      • Recommended Cord Grips
      • Shield Terminating Connectors
    • Electromagnetic Compatibility (EMC)
      • General Notes (Bulletin 294D only)
    • Ethernet, DeviceNet, and I/O Connections
      • DeviceNet Connector (M18)
    • ArmorConnect Power Media Receptacles
    • Optional Locking Clip
    • Notes:
• Chapter 3
  • Product Commissioning
    • Configuring DeviceNet Address
      • Manually Configure the Network Address Switches
    • DeviceNet™ Commissioning
    • Establishing a DeviceNet Node Address
    • Node Commissioning using Hardware
    • Node Commissioning using Software
    • Registering an EDS file
    • Using the Node Commissioning Tool Inside RSNetWorx for DeviceNet
    • System Configuration
• Chapter 4
  • Bulletin 290D/291D/294D Programmable Parameters
    • Electronic Data Sheet (EDS)
    • Basic Setup Parameters
      • Parameter Groups
    • ArmorStart LT DeviceNet Parameters
      • Introduction
      • Parameter Programming
    • Bulletin 290D/291D
      • Basic Status Group
      • Trip Status Group
      • Basic Configuration Group
      • Starter Protection Group
      • User I/O Configuration Group
      • Miscellaneous Configuration Group
      • Advanced Configuration
    • Bulletin 294D
      • Basic Status Group
      • Trip Status Group
      • Motor and Control Group
      • Speed Control Group
      • Starter Protection Group
      • User I/O Configuration Group
      • Miscellaneous Configuration Group
      • Advanced Configuration
• Chapter 5
  • Diagnostics
    • Overview
    • Status LEDs and Reset
    • Fault Diagnostics
      • Protection Faults
    • Quick Reference Troubleshooting
    • Fault LED Indications
      • Bulletin 290D/291D Faults
    • Bulletin 294D Faults
• Chapter 6
  • Specifications
    • Bulletin 290D/291D
    • Motor Overload Trip Curves
      • Bulletin 100-K/104-K Life-Load Curves
    • Bulletin 294D
      • Motor Overload Trip Curves
• Appendix A
  • Applying More Than One ArmorStart LT Motor Controller in a Single Branch Circuit on Industrial Machinery
    • Introduction
    • ArmorStart LT Product Family
    • Multiple-Motor Branch Circuits and Motor Controllers Listed for Group Installation – General
    • Maximum Fuse Ampere Rating According to 7.2.10.4(1) and 7.2.10.4(2)
      • Complete Text -
    • Explanatory Example
    • Input and Output Conductors of Bulletin 290D and 291D Controllers (a)
    • Input and Output Conductors of Bulletin 294D Controllers (b)
    • Combined Load Conductors (c)
• Appendix B
  • CIP Information
    • High Level Product Description
      • Product Codes and Name Strings
    • CIP Explicit Connection Behavior
      • EDS Files
    • CIP Object Requirements
    • Identity Object
      • CLASS CODE 0x0001
    • Message Router
      • CLASS CODE 0x0002
    • DeviceNet Object
    • Assembly Object
      • CLASS CODE 0x0004
      • I/O Assemblies
    • Connection Object
      • CLASS CODE 0x0005
    • Discrete Input Point Object
      • CLASS CODE 0x0008
    • Discrete Output Point Object
      • CLASS CODE 0x0009
      • Discrete Output Point Object Special Requirements
    • Analog Input Point Object
      • CLASS CODE 0x000A (Implemented in Bulletin 294D units only)
    • Analog Output Point Object
      • CLASS CODE 0x000B (Implemented in Bulletin 294D units only)
    • Parameter Object
      • CLASS CODE 0x000F
    • Parameter Group Object
      • CLASS CODE 0x0010
    • Discrete Input Group Object
      • CLASS CODE 0x001D
    • Discrete Output Group Object
      • CLASS CODE 0x001E
    • Control Supervisor Object
      • CLASS CODE 0x0029
    • Overload Object
      • CLASS CODE 0x002C
    • DPI Fault Object
      • CLASS CODE 0x0097
    • DPI Alarm Object
      • CLASS CODE 0x0098
    • DeviceNet Interface Object
      • CLASS CODE 0x00B4
    • ZIP Object
      • CLASS CODE 0x032E
      • ZIP Enable
      • Attribute Symantics
      • Behavior
    • Notes:
• Appendix C
  • Using DeviceLogix™
    • Introduction
    • DeviceLogix Programming
      • DeviceLogix Programming Example
• Back Page