Lucent Technologies MN10285K User Manual
Lucent Technologies Notebooks
Advertising
Table of contents
Document Outline
- Cover
- Contents
- List of Tables
- List of Figures
- About This Manual
- 1 General Description
- 2 Interrupts
- 3 Low-Power Modes
- 4 Timers
- 4.1 8-Bit Timer Description
- 4.2 8-Bit Timer Features
- 4.3 8-Bit Timer Block Diagrams
- 4.4 8-Bit Timer Timing
- 4.5 8-Bit Timer Setup Examples
- 4.6 8-Bit Timer Control Registers
- 4.7 16-Bit Timer Description
- 4.8 16-Bit Timer Features
- 4.9 16-Bit Timer Block Diagrams
- 4.10 16-Bit Timer Timing
- 4.11 16-Bit Timer Setup Examples
- 4.11.1 Setting Up an Event Counter Using Timer 4
- 4.11.2 Setting Up a Single-Phase PWM Output Signal Using Timer 4
- 4.11.3 Setting Up a Two-Phase PWM Output Signal Using Timer 4
- 4.11.4 Setting Up a Single-Phase Capture Input Using Timer 4
- 4.11.5 Setting Up a Two-Phase Capture Input Using Timer 4
- 4.11.6 Setting Up a 4x Two-Phase Encoder Input Using Timer 5
- 4.11.7 Setting Up a 1x Two-Phase Encoder Input Using Timer 5
- 4.11.8 Setting Up a One-Shot Pulse Output Using Timer 5
- 4.11.9 Setting Up an External Count Direction Controller Using Timer 5
- 4.11.10 Setting Up External Reset Control Using Timer 5
- 4.12 16-Bit Timer Control Registers
- 5 Serial Interfaces
- 6 Analog-to-Digital Converter
- 7 On-Screen Display
- 7.1 Description
- 7.2 Features
- 7.3 Block Diagram
- 7.4 Power-Saving Considerations in the OSD Block
- 7.5 OSD Operation
- 7.6 Standard and Extended Display Modes
- 7.7 Display Setup Examples
- 7.8 VRAM
- 7.9 ROM
- 7.10 Setting Up the OSD
- 7.11 DMA and Interrupt Timing
- 7.12 Selecting the OSD Dot Clock
- 7.13 Controlling the Shuttering Effect
- 7.14 Field Detection Circuit
- 7.15 OSD Registers
- 8 IR Remote Signal Receiver
- 9 Closed-Caption Decoder
- 10 Pulse Width Modulator
- 11 I/O Ports
- 12 ROM Correction
- 13 I2C Bus Controller
- 13.1 Description
- 13.2 Block Diagram
- 13.3 Functional Description
- 13.4 Setting Up the I2C Bus Connection
- 13.5 SDA and SCL Waveform Characteristics
- 13.6 I2C Interface Setup Examples
- 13.7 I2C Bus Interface Registers
- 14 H Counter
- Appendix A Register Map
- Appendix B MN102HF75K Flash EEPROM Version
- B.1 Description
- B.2 Benefits
- B.3 Using the PROM Writer Mode
- B.4 Using the Onboard Serial Programming Mode
- B.4.1 Configuring the System for Onboard Serial Programming
- B.4.2 Circuit Requirements for the Target Board
- B.4.3 Microcontroller Hardware Used in Onboard Serial Programming
- B.4.4 Microcontroller Memory Map Used During Onboard Serial Programming
- B.4.5 Microcontroller Clock on the Target Board
- B.4.6 Setting Up the Onboard Serial Programming Mode
- B.4.7 Branching to the User Program
- B.5 Reprogramming Flow
- B.6 Programming Times
- Record of Changes
- Colophon
- Sales Offices