Basler Electric BE1-700 Modbus Protocol - Manual (Page 83)

9376700991 Rev D BE1-700 Modbus™ Protocol 4-3
ASCII Command Modbus™ Registers
S#-792=<second auto reclose delay> 40408-40409
S#-793=<third auto reclose delay> 40410-40411
S#-794=<fourth auto reclose delay> 40412-40413
S#-79R=<reset time delay> 40414-40415
S#-79F=<reclose fail time delay> 40416-40417
S#-79M=<max reclose time> 40418-40419
S#-79P=<pilot time delay> 40420-40421
S#-79SCB=<sequence control> 40422
S#-81=<pickup>,<time delay>,<mode> 40460-40461, 40462-40463, 40464
S#-181=<pickup>,<time delay>,<mode> 40465-40466, 40467-40468, 40469
S#-281=<pickup>,<time delay>,<mode> 40470-40471, 40472-40473, 40474
S#-381=<pickup>,<time delay>,<mode> 40475-40476, 40477-40478, 40479
S#-481=<pickup>,<time delay>,<mode> 40480-40481, 40482-40483, 40484
S#-581=<pickup>,<time delay>,<mode> 40485-40486, 40487-40488, 40489
S#-81INH=<Va>,<VQ>,<overfreq>,<underfreq> 40490-40491, 40492-40493, 40494-40495,
40496-40497
S#-62=<time delay 1>,<time delay2> 40359-40360, 40361-40362
S#-162=<time delay 1>,<time delay2> 40363-40364, 40365-40366
S#-24=<pickup>, <time delay>, <reset delay> 40516-40517, 40518-40519, 40520-40521
S#-25=<delta volts>, <phase angle>,
<frequency>, <mode>
40522-40523, 40524-40525, 40526-40527, 40528
S#-25VM=<live volts>, <dead volts>, <time
delay>, <mode1>
40529-40530, 40531-40532, 40533-40534,
40535-40536
SA-BKR1=<mode>,<alarm limit> 41096, 41097-41098
SA-BKR2=<mode>,<alarm limit> 41099, 41100-41101
SA-BKR3=<mode>,<alarm limit> 41102, 41103-41104
SA-DIP=<alarm level> 41259-41260
SA-DIN=<alarm level> 41261-41262
SA-DIQ=<alarm level> 41263-41264
SA-LGC=<alarm number> 41269-41270
SA-MAJ=<alarm number> 41265-41266
SA-MIN=<alarm number> 41267-41268
SA-RESET=<reset Alarm Logic> 41419-41424, 41427-41432
SA-24 = <Volts / Hertz alarm level> 41247
SB-DUTY=<exponent>,<dmax.>,<blk bkr logic> 41092-41093, 41094-41095, 41110-41115,
41118-41123
SB-LOGIC=<breaker close logic equation> 41126-41131, 41134-41139
SG-BL=<LCD timer> 41218
SG-CLK=<date format>,<time format>
<dst enable>
41272, 41273, 41274
SG-COM0=<baud rate>,<flow control>,<page
length>,<ack>
40962, 40964, 40965, 40966
SG-COM1=<baud rate>,<relay address>,<flow
control>,<page length>,<ack>
40971, 40972,40973, 40974, 40975
SG-COM2=<baud rate>,<relay address>,,,,,
<parity>,<remote delay>,<stop bits>
40980, 40981, 40986, 40987, 40988
SG-CTP=<ratio> 41021
SG-CTG=<ratio> 41022
SG-VTP=<VT ratio>,<connection>,<27/59
mode>,<51/27R mode>
41033-41034, 41035-41036, 41037-41038,
41039-41040
SG-VTX=<aux VT ratio>,<connection> 41041-41042, 41043-41044
SG-NOM=<nom volts>,<nom amps> 40602-40603, 40604-40605
SG-DIP=<alarm interval>,<calculation method> 41275
SG-DIN=<alarm interval>,<calculation method> 41276
SG-DIQ=<alarm interval>,<calculation method> 41277
SG-FREQ=<frequency> 41018
SG-HOLD=<output hold enable> 41284