MacDon FD70 for Combine Operators - Manual (Page 27)

SECTION 6. SPECIFICATIONS
Form 169006
25
Revision D
6 SPECIFICATIONS
HEADER MODEL D60 D50 / D60 D50 / D60 / FD70 D60 / FD70 D60 / FD70
HEADER SIZE 20 FT 25 FT 30 FT 35 FT 40 FT 45 FT
OVERALL
Width
(Inches (mm))
Transport (Reel Full
Aft) With CA20 Adapter
96 (2438)
Field 255.1 (6479) 315.1 (8003) 375.1 (9527) 435.1 (11051) 495.1 (12575) 555.1 (14099)
Length
(Inches (mm))
Transport
(with Tow
Pole)
D50, D60 Not Applicable 505.7 (12845) 547.5 (13907)
601.5 (15278) 631.5 (16040)
FD70 Not Applicable 513.0 (13029) 556.7 (14141)
Height -Transport 97 in. (2464 mm)
Estimated Weight Range
Base Header - No Adapter
(lb (kg))
D50 Not Applicable 3500 (1589) 4150 (1884) 4700 (2134) Not Applicable
D60 3400 (1544)
3500 - 4100
(1589 - 1861)
4200 - 5100
(1907 - 2315)
4700 - 5700
(2134 - 2588)
5400 - 5800
(2451 - 2633)
6200 (2815)
FD70 Not Applicable 4850 (2202) 5250 (2384)
5700 - 5900
(2588 - 2979)
6300 (2860)
CUTTERBAR
Width (Inches (mm) 240 (6096) 300 (7620) 360 (9144) 420 (10668) 480 (12192) 540 (13716)
Header Cutting Height
Shortest Center-Link
1.3 in. (32 mm) below ground -
52.3 in. (1328 mm) above
0.8 in. (20 mm) below ground - 52.8 in. (1340 mm) above
Longest Center-Link
4.6 in. (117 mm) below ground
- 46.9 in. (1192 mm) above
4.1 in. (105 mm) below ground - 47.4 in. (1204 mm) above
Guard Angle (Cutterbar on Ground) 7.0° - 12.4° 2.0° - 7.4°
SICKLE
Drive Type
SK Hydraulic Motor / ‘C’ Belt/Heavy Duty (MD) Wobble Box
DK (Except D50)
Hydraulic Motor / Two ‘B’ Timing Belts / Two Heavy Duty (MD)
Wobble Boxes
Two Hydraulic Motors To "C"
Belts, Untimed To Heavy Duty
(MD) Wobble Boxes.
Sickle Speed
SK 1200 Strokes Per Minute Not Applicable
DK 1380 Strokes Per Minute
Stroke 3 in. (76 mm)
Sections - Over-Serrated
& Bolted (serrations/inch)
Cut-Out or Solid 14 9 / 14 9
Guards and
Hold-Downs
Pointed
D50 Not Applicable Pointed / Case Hardened / Sheet Metal / Adjuster Bolt Not Applicable
D60 Case Hardened or Double Heat Treated / Sheet Metal / Adjuster Bolt
FD70 Not Applicable Double Heat Treated / Sheet Metal / Adjuster Bolt
Stub (Except D50)
Sheet Metal
HD
Sheet Metal or
Forged HD
Not Applicable
CONVEYOR AND DECKS
Draper Drive Hydraulic
Draper Width 41.6 in. (1057 mm)
Draper Speed 247 - 464 ft/min (75 - 141 m/min)
Delivery Opening
Width
D50 Not Applicable 73.6 in. (1870 mm) Not Applicable
D60 73.6 in. (1870 mm)
FD70 Not Applicable 73.6 in. (1870 mm)
Height 37.2 - 41.7 in. (945 - 1058 mm)
Draper Angle
(Cutterbar on Ground)
D50, D60 13.0° - 18.4°
FD70 Not Applicable 14.0° - 19.4°