Verilink APS 2000 T1 Line Protection (880-502411-001) Product Manual - Manual (Page 40)

Configuration
3-12 Verilink APS 2000 User Manual
Configuration Menu
Access the Configuration Menu by typing "C" at the APS 2000 Main
Menu.
Figure 3-7 APS Configuration Menu
Configuration
Menu Commands
Some of the commands on the CSU Configuration Menu are shown
on both the left and right sides of the screen. Commands that are
used for both DSX-1 equipment and T1 network ports are repeated
on both the equipment and the net side of the diagram. Command
prompts for these options present pairs of values: the value for the
equipment side is followed by the value for the network side.
For example, if connecting a D4 (SF) channel bank to an ESF T1
circuit the SF,ESF framing selection would be used.
Table 3-5 below describes all of the SCC 2020 CSU Configuration
Menu options:
APS CONFIGURATION -- FW Rev 4.0 HW Fab 0.8 Type TAC 2110 -- APS CONFIGURATION -- FW Rev 4.0 HW Fab 0.8 Type TAC 2110 -- APS CONFIGURATION -- FW Rev 4.0 HW Fab 0.8 Type TAC 2110 -- APS CONFIGURATION -- FW Rev 4.0 HW Fab 0.8 Type TAC 2110 --
|-----------------------| |-----------------------| |-----------------------| |-----------------------|
-------<< eq <<-------| K) aps control AUTO |-------<< net <<-------
-------<< eq <<-------| K) aps control AUTO |-------<< net <<------- -------<< eq <<-------| K) aps control AUTO |-------<< net <<------- -------<< eq <<-------| K) aps control AUTO |-------<< net <<-------
W) framing SF | | W) framing ESF
W) framing SF | | W) framing ESF W) framing SF | | W) framing ESF W) framing SF | | W) framing ESF
F) format AMI | | F) format B8ZS
F) format AMI | | F) format B8ZS F) format AMI | | F) format B8ZS F) format AMI | | F) format B8ZS
J) jitt buf 40 BITS | | J) jitt buf 40 BITS
J) jitt buf 40 BITS | | J) jitt buf 40 BITS J) jitt buf 40 BITS | | J) jitt buf 40 BITS J) jitt buf 40 BITS | | J) jitt buf 40 BITS
R) eq crc REGEN | | R) net crc REGEN
R) eq crc REGEN | | R) net crc REGEN R) eq crc REGEN | | R) net crc REGEN R) eq crc REGEN | | R) net crc REGEN
Y) xcode yel OFF | | Y) xcode yel OFF
Y) xcode yel OFF | | Y) xcode yel OFF Y) xcode yel OFF | | Y) xcode yel OFF Y) xcode yel OFF | | Y) xcode yel OFF
M) distance 0-133 | | L) lbO 0 DB
M) distance 0-133 | | L) lbO 0 DB M) distance 0-133 | | L) lbO 0 DB M) distance 0-133 | | L) lbO 0 DB
|-----------------------| Z) density 12%+80z
|-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z
X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config
A) loop code/test ptns FULL T1 Code/PTN B) diu clock THRU A) loop code/test ptns FULL T1 Code/PTN B) diu clock THRU A) loop code/test ptns FULL T1 Code/PTN B) diu clock THRU A) loop code/test ptns FULL T1 Code/PTN B) diu clock THRU
P) prm OFF
P) prm OFF P) prm OFF P) prm OFF
D) select D&I DS0s (1,-,24)
D) select D&I DS0s (1,-,24) D) select D&I DS0s (1,-,24) D) select D&I DS0s (1,-,24)
_ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
G) Alarm ENABLE
G) Alarm ENABLE G) Alarm ENABLE G) Alarm ENABLE
[1,1] NEAR TAC 2110 >
[1,1] NEAR TAC 2110 > [1,1] NEAR TAC 2110 > [1,1] NEAR TAC 2110 >