Pioneer CDJ-400 - Manual (Page 11)

BEFORE OPERATING (PANEL FACILITIES)
11
<DRB1451>
En
English
22. TRACK SEARCH buttons ( 4, ¢)
Changes tracks in the forward/reverse direction. ( ☞P.15)
23. Reverse button (DIRECTION REV) ( ☞P. 18)
When this button is pressed, its indicator lights and the unit is
set to reverse play.
24. LOOP buttons
7 IN/REALTIME CUE/HOT LOOP button/indicator
Use to input loop-in point. (IN
☞P.18)
Use to set the current playback point as cue point. (REALTIME
CUE
☞P.17)
When pressed during loop play, returns playback to loop-in
point and begins replay. (HOT LOOP
☞P.18)
7 OUT/OUT ADJUST button/indicator
Use to input loop-out point. (OUT
☞P.18)
When pressed during loop play, adjusts loop-out point. (OUT
ADJUST
☞P.18)
7 RELOOP/EXIT button
After finishing loop play, the stored loop-in/out information
can be used to begin loop play again. (RELOOP
☞P.18)
When pressed during loop play, loop play stops and playback
returns to normal playback mode. (EXIT
☞P.18)
7 BEAT LOOP/LOOP DIVIDE buttons/indicator
If pressed while playing or pausing a track, the loop-end will
be calculated based on the BPM (Beat Per Minute) of the track,
and loop-play will then start (BEAT LOOP
☞P.18).
Pressing the – button during loop-playback will divide the
playback loop, and pressing the + button will return the
playback loop to its original length (LOOP DIVIDE
☞P.18).
During loop-playback, the button’s indicator will light to
indicate that the LOOP DIVIDE button is enabled.
Rear Panel
1. USB port
Use to connect a computer.
2. AUDIO OUT L, R connectors
RCA-type analog audio output jacks.
3. CONTROL connector
When the accessory control cord is used to connect this con-
nector to the corresponding CONTROL connector on a Pio-
neer DJ mixer, the DJ mixer can be used to control the CD
player for fader start play and back cue.
Also, by connecting this connector to the CONTROL connec-
tor on another Pioneer DJ CD player, automatic relay play can
be performed. (
☞ P. 19)
4. DIGITAL OUT connector
RCA type coaxial digital output connectors used to connect a
DJ mixer or AV amplifier, CD player, etc., equipped with dig-
ital input connectors. The digital outputs here support all DJ
and other functions, but only audio data is output (without
subcodes; CD graphics are not supported).
5. AC inlet (AC IN)
Use the accessory power cord to connect this inlet to a stand-
ard AC power outlet.
6. POWER
— OFF/_ ON switch
5
3 4 1
6
2
25. SCRATCH JOG EFFECT/DIGITAL JOG BREAK
buttons
The button’s function changes depending on the JOG mode.
7 SCRATCH JOG EFFECT buttons
Turns on/off each of the effects BUBBLE, TRANS, and WAH
during VINYL mode (
☞P.16).
7 DIGITAL JOG BREAK buttons
Turns on/off each of the effects JET, ROLL, and WAH during
CDJ mode (
☞P.16).
26. SOURCE SELECT buttons
7 USB select button
Select when playing files from a connected USB memory de-
vice. Each time the button is pressed, the function alternates
between USB and PC.
7 CD select button
Select when playing CDs or files on a CD-ROM.
27. USB port
Use to connect a USB memory device.
28. TEXT MODE/UTILITY MODE button
Changes the TEXT display ( ☞P.12)
Hold the button depressed to enter utility setting mode.
29. TIME MODE/AUTO CUE button
Switches the display between the track’s elapsed time and re-
maining time (
☞P.12).
Hold the button depressed to turn the auto cue function on/off
(
☞P.14).
30. Jog touch indicators
During VINYL mode, lights when the top of the jog dial is
pressed.