Cub Cadet SLTX1000 Series - Manual (Page 273)

310-0510 IHT 35
310-0510 ITEMS LIST
No. DESCRIPTION No. DESCRIPTION
1 Main Housing, Assembly
Main Housing, Machined
Bushing .865 x .985 x .790
Pin, Standard Headless
2 Side Housing, Assembly
Side Housing, Machined
Bushing .865 x .985 x .790
Bushing .624 x .719 x .562
3 Center Section Assembly
Center Section Machined (5 piston)
Bushing .707 x .788 x .591
4 Swashplate, Trunnion Machined
5 Block - Assembly
Block - Cylinder
Pistons
Springs, Compression
Thrust - Washer
6 Sealant (10.1 oz.)
7 Hex Flange Screw 1/4-20 x 1.25
8 Stud, 5/16-24 Hex Double End
9 Shaft, Input
10 Ring - Retaining
11 Washer, Flat 1.23 x 1.57 x .04
12 Ring - Retaining
13 Seal, Lip 17 x 40 x 7
14 Ball Bearing 17MM x 40MM x 12MM
16 Hex Flange Head Screw 5/16-24 x 0.94 w/patch
17 Lip Seal 18 x 32 x 7
18 Arm, Control
19 Bearing, 30 x 52 x 13 Thrust
23 Check Plug Assembly, .027 Bleed, Washer (“A” port)
24 Shaft, Motor
27 Gear - Pinion, 13T
28 10T/48T Gear
29 Gear, 10T Jackshaft
30 60T Bull Gear
31 Sleeve Bushing (Inboard)
32 Sleeve Bushing .75 x 1.575 x .625
33 Washer, .77 x 1-1/2 x .10 THK
34 Lip Seal Axle Seal
35 Shaft, Axle .75 x 11.39 (DD, R.H.)
36 Shaft, Axle .75 x 17.99 (DD, L.H.)
37 Miter Gear 12T (Splined)
38 Miter Gear 12T (0.5 ID)
39 Pin
40
Ring, Spiral Retaining
41 Pin, Jackshaft
42 Magnet, Ring
43 Spring, Bypass
44 Bolt, Hex Flange 3/8-24 x 2.5
45 Filter
46 Base,
Filter
47 Actuator, Bypass
48 Rod, Bypass Actuator
49 Arm, Bypass
50 Retaining Ring .250 External
51 Seal, Lip .250 x .750 x .250TC
52 Flat Washer, 5/8 x 1.0 x .05
53 Retaining Ring
55 Spring - Helical Compression
56 Washer, Thrust .59 x .79 x .04
57 20W-50 Oil
58 Brake Yoke
59 Rotor, Brake
60 Brake Puck
61 Puck Plate
62 Brake Actuating Pin
63 Bolt, Hex Hd 1/4-20 x 2 w/patch
65 Spacer
66
Spring, Brake Arm Bias
68 Arm, Brake
69 Nut, Castle 5/16-24
70 Cotter Pin 3/32 x 3/4
71 Compression Spring, Brake, Anti-Drag
72 Washer, HT .51 x 1.0 x .03
73 Flat - Washer .34 x .88 x.06
74 Oil Seal .625 x 1.0 x .25
75 Check Plug Assembly, .027 Bleed, Washer (“B” port)
84 Fitting, 5/16 SAE 5/32 Tube
85 Hose, Expansion Tank
87 Cap - Vent
88 Bolt, Self Tapping 10-32 x 1/2
94 Bearing, Ball .62 x 1.38 x.44
95 Screw, Socket Hd Cap 5/16-24 x 1.5
96 Spacer, Locating
97 Screw, Countersunk 5/16-18 1.0
98 Arm, Return
99 Puck, Adjusting
100 Washer, Flat .32 x 1.60 x .24
101 Spring, Extension Double Loop
102 Spacer .26 x .56 x .87
103 Bracket, Torque
107 Deflector
108
Washer, Flat .71 x 1.16 x .04
109 Plug, 9/16-18 (Metal)
110 Screw, Torx Hd 5/16-18 x 1.5
111 O-Ring .299 x .505 x .103
113 Bracket, Support Expansion Tank
114 Spring Guide
124 Center Section-Filter-Bypass Assy
Center Section (5 piston)
Base Filter (w/poppet)
Check Plug Assy. .027 Bleed, Washer
Spring, Bypass .50 in
Actuator, Bypass
Deflector
Bottom, Filter
Bushing, .707 x .788 x .591
125 Filter Assembly
Bottom, Filter
Spring, Bypass .50 in
Actuator, Bypass
Deflector
Base,
Filter w/poppet
127 Kit, Seal & O-Ring
Seal, Lip 17 x 40 x 7
Seal, Lip 18 x 32 x 7
Seal Lip .75 x 1.577 x .250
Seal, Lip .250 x .750 x .250 TC
Seal, Lip .625 x 1.0 x .25
O-Ring .299 x .505 x .103
128 Kit, Expansion Tank
Tank, Expansion Assembly
Cap, Expansion
Bolt, Self Tapping 10-32 x 1/2
Bracket, Expansion Tank
200 Kit, 60T Bull Gear Diff Pins
Gear, 60T
Pin, 0.5 OD