H3C Technologies H3C S10500 Series Switches User Manual

Page 158

Advertising

147

# Assign Ten-GigabitEthernet 1/0/1 to VLAN 1001 as an untagged member.

[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid vlan 1001 untagged

# Assign Ten-GigabitEthernet 1/0/1 to VLAN 4001 as a tagged member.

[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid vlan 4001 tagged

# Set the PVID to VLAN 1001 for Ten-GigabitEthernet 1/0/1.

[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid pvid vlan 1001

# Enable STP on Ten-GigabitEthernet 1/0/1.

[SwitchA-Ten-GigabitEthernet1/0/1] stp enable

[SwitchA-Ten-GigabitEthernet1/0/1] quit

# Configure interface Ten-GigabitEthernet 2/0/1 as a hybrid port.

[SwitchA] interface ten-gigabitethernet 2/0/1

[SwitchA-Ten-GigabitEthernet2/0/1] port link-type hybrid

# Assign Ten-GigabitEthernet 2/0/1 to VLAN 1001 as an untagged member.

[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid vlan 1001 untagged

# Assign Ten-GigabitEthernet 2/0/1 to VLAN 4002 as a tagged member.

[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid vlan 4002 tagged

# Set the PVID to VLAN 1001 for Ten-GigabitEthernet 2/0/1.

[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid pvid vlan 1001

# Enable STP on Ten-GigabitEthernet 2/0/1.

[SwitchA-Ten-GigabitEthernet2/0/1] stp enable

[SwitchA-Ten-GigabitEthernet2/0/1] quit

# Configure interface Ten-GigabitEthernet 1/0/10 as a trunk port, and assign the interface to
VLAN 1001.

[SwitchA] interface ten-gigabitethernet 1/0/10

[SwitchA-Ten-GigabitEthernet1/0/10] port link-type trunk

[SwitchA-Ten-GigabitEthernet1/0/10] port trunk permit vlan 1001

# Enable STP on Ten-GigabitEthernet 1/0/10.

[SwitchA-Ten-GigabitEthernet1/0/10] stp enable

[SwitchA-Ten-GigabitEthernet1/0/10] quit

# Configure interface Ten-GigabitEthernet 2/0/10 as a trunk port, and assign the interface to

VLAN 1001.

[SwitchA] interface ten-gigabitethernet 2/0/10

[SwitchA-Ten-GigabitEthernet2/0/10] port link-type trunk

[SwitchA-Ten-GigabitEthernet2/0/10] port trunk permit vlan 1001

# Enable STP on Ten-GigabitEthernet 2/0/10.

[SwitchA-Ten-GigabitEthernet2/0/10] stp enable

[SwitchA-Ten-GigabitEthernet2/0/10] quit

# Create Layer 2 aggregate interface 1, and configure it to operate in dynamic aggregation
mode.

[SwitchA] interface bridge-aggregation 1

[SwitchA-Bridge-Aggregation1] link-aggregation mode dynamic

# Disable STP on Layer 2 aggregate interface 1.

[SwitchA-Bridge-Aggregation1] undo stp enable

[SwitchA-Bridge-Aggregation1] quit

Advertising

This manual is related to the following products:

H3C S12500 Series Switches, H3C S6800 Series Switches, H3C S5820V2 Series Switches, H3C S5830V2 Series Switches, H3C S6300 Series Switches

Popular Brands

Popular manuals