Setting an mtc offset value, Setting an mtc offset value (“mtc offset” menu), Setting an mtc frame rate – Fostex D1624 User Manual
Page 110: Setting an mtc offset, Turn the jog dial to enter the desired frame rate, Press the execute/yes key, Flashing
110
D824/D1624 Reference Manual (Changing the Initial Settings <SETUP mode>)
44.1kHz
SETUP
MTC
OFFSET
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
MTC
OFFSET
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
Flashing
Flashing
Setting an MTC frame rate
1.While the recorder is stopped, press the SETUP
key to enter SETUP mode.
2.Turn the JOG dial to select [Frame Rate (?)] ( [?]
flashes), then press the EXECUTE/YES key.
The current frame rate setting appears on the display.
Press the EXECUTE/YES key to turn off the flashing [?]
character; the current setting flashes.
The initial setting of [25] flashes as shown below.
3.Turn the JOG dial to enter the desired frame rate.
Rotating the JOG dial clockwise or counter-clockwise
displays available frame rates as an alternative.
4.Press the EXECUTE/YES key.
The selected frame rate is stored and the display returns
to the indication with a flashing [?] that appeared in
step 2.
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
<Note>
There are no 29.97nd or 29.97df in the MTC standard.
Use either 30nd or 30df unless you definitely need to
synchronize the recorder with NTSC video.
Setting an MTC offset value (“MTC OFFSET” menu)
The “Setting an MTC offset value” menu enables you to specify an offset time value - the difference between
the time of MTC output from the recorder and the ABS 00m 00s 00f 00sf time. You need to specify this value
if you have selected [Mtc] for the “Setting MIDI sync output signal” menu.
With the initial setting of 00h 59m 57s 00f 00sf, for example, MTC of 59m 57s 00f 00sf is output at the ABS
time 00m 00s 00f 00sf. You can also set an offset value from the 001bar 1beat 00clk value (bar/beat) on the
Tempo Map. Refer to the next section for information on MTC Offset mode.
• Initial setting:
[00h: 59m: 57s: 00f: 00sf]
• Setting range of offset time:
00h: 00m: 00s: 00f: 00sf - 23h: 59m: 59s: 29f: 99sf
* You can set the value for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
Setting an MTC offset
1.While the recorder is stopped, press the SETUP
key to enter SETUP mode.
2.Turn the JOG dial to select [MTC OFFSET] ([MTC
OFFSET] flashes.), then press the EXECUTE/YES
key.
The current offset value appears on the display.
Pressing the EXECUTE/YES key turns off the flashing
[MTC OFFSET] character, and the value in seconds
flashes.
You can enter a value at the flashing digit. The number
[57] of the initial setting [57s] flashes as shown below.