Fostex D1624 - Manual (Page 12)

D824/D1624 Reference Manual (Names and Functions)
12
11. Display Select key [DISP SEL]
This key is used to change the display mode. Pressing
this key repeatedly will change the display mode as
follows:
* Refer to page " 24 " in regards to REMAIN, page " 101 "
on the SETUP menu, and the APPENDIX on details if
the Model 8345 TC/SYNC card is installed.
Pressing this key while holding down the SHIFT key
will switch the Time Base (*) as follows. The Time
Base can be set when the display shows the recorder’s
current position or the available disk space
(REMAIN).
* Refer to pages “ 23 ” and “ 105 ” for more information
about MTC and the internal Tempo Map.
(*) Time Base:
The recorder uses time display (ABS or MTC) or Bar/Beat/
Clock display to indicate the current position of the
recorder section. These displays are called “Time Base.”
ABS (Absolute Time) shows the absolute time of the disk,
and MTC (MIDI Time code) shows the relative time obtained
by adding an MTC offset value to the ABS value.
Bar/Beat/Clock (BAR/BEAT/CLK) indicates a position
within a piece of music and conforms to the MIDI clock
and Song Position Pointers created on the internal Tempo
Map.
10. Auto Return End key [AUTO RTN END]
This key is used to store and recall the end point
(AUTO RTN END point) for the Auto Return or Auto
Repeat operation. You can locate a stored AUTO
RTN END point. If you press the AUTO RTN END
key while holding down the SHIFT key when the
recorder is stopped, you can preview the fade-out
part at the stored AUTO RTN END point.
* Refer to page “ 57 ” for locating the AUTO RTN END
point.
* Refer to page “ 66 ” for copying/moving data.
* Refer to page “ 63 ” for previewing data at the AUTO
RTN END point.
12. Program select key [PGM]
When this key is pressed, the mode will change to
setup for a new program and allow program
selecting.
* Refer to page “ 35 ” for program select function.
13. Store key [STORE]
This key is used to store a time value (or Bar/Beat/
Clock value) to one of the memory keys. Pressing
this key, and then one of the following keys will cause
the data shown on the display to be stored to the
corresponding memory key you pressed.
* Refer to page “ 57 ” for more information about the
Locate function.
* Refer to page “ 39 ” for more information about Auto
Punch In/Out recording.
* Refer to page “ 57 ” for more information about Auto
Return.
After pressing this key, if you wish to cancel the
store operation, press the EXIT/NO key, or STOP
button.
Data is stored as an Auto Return End point. The
stored data can be used as a locator.
If an optional Model 8345 TC/SYNC card is installed,
information in the MTC IN or TC IN will differ
depending on [Ref. TC?] menu setting (MTC or LTC)
in the SETUP mode. If the card is not installed, [00h
00m 00s 00f 00sf] will always be displayed.
STORE -> CLIPBOARD IN
Data is stored as a Clipboard In point. The stored
data can be used as a locator.
STORE -> CLIPBOARD OUT
Data is stored as a Clipboard Out point. The
stored data can be used as a locator.
STORE -> AUTO PUNCH IN
Data is stored as an Auto Punch In point. The
stored data can be used as a locator.
STORE -> AUTO PUNCH OUT
Data is stored as an Auto Punch Out point. The
stored data can be used as a locator.
STORE -> AUTO RTN START
Data is stored as an Auto Return Start point.
The stored data can be used as a locator.
STORE -> AUTO RTN END
The current position
Disk space (remain)
MTC IN or TC IN display
ABS time base
Bar/beat/clk time base
MTC time base
Using [Press LOCATE: **] displayed after pressing
the RECALL key, data stored in the desired locate
number (00~99) can be recalled.
STORE -> ([Press LOCATE:**]) -> LOCATE