Fostex D1624 - Manual (Page 113)

113
D824/D1624 Reference Manual (Changing the Initial Settings <SETUP mode>)
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
Flashing
Recording enabled/disabled
1.While the recorder is stopped, press the SETUP
key to enter SETUP mode.
2.Turn the JOG dial to select [Rec Protct ?] ([?]
flashes), then press the EXECUTE/YES key.
The current setting appears on the display.
Pressing the EXECUTE/YES key turns off the flashing [?]
character, and the recording enabled/disabled indicator
flashes. With the initial setting, [Off] flashes as shown
below.
3.Use the JOG dial to enable or disable recording.
Rotating the JOG dial clockwise and counter-clockwise
will flash [On] and [Off] alternately.
Selecting [Off] enables recording; you can record, paste,
and erase data.
Selecting [On] disables recording; and you cannot record,
paste, or erase data.
<Note>
When recording is disabled (On) and you try to record,
paste, or erase data, the recorder displays [Protected]
for a second, indicating that you cannot perform the
operation. To perform the operation, you need to enable
recording (Off).
4.Press the EXECUTE/YES key.
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
Setting digital input (“D. in ?” menu)
In the “Setting a digital input” menu, the signal to be input to the DIGITAL/DATA IN connector of the recorder
can be set for either digital signals (adat digital signal or S/P DIF digital signal) or analog signals, and also
setup of the digital in clock (synchronous or asynchronous).
By using this function, signals from external digital equipment (CD, MD, DAT, adat digital mixer) can be
digitally recorded. If “SP DIF” is selected, the S/P DIF L, R signals input to DIGITAL/DATA IN 1-8 will be
assigned to tracks 1 and 2, and if “adat” is selected, adat signals input to DIGITAL/DATA IN 1-8 will be
assigned to tracks 1-8 (In D1624, adat signals input to DIGITAL/DATA IN 9-16 will go to tracks 9-16).
When selecting the clock, there are the Async and Sync modes; either should be selected depending on the
application. If it is set to “Async mode,” the later explained [Clock Sel?] (Setting the operating clock) should
be setup in accordance to the application.
• Initial setting: Analog
• Assignable digital signal/setting digital in-clock: adat: Async (adat digital signal/Asynchronous mode)
adat: Sync (adat digital signal/Synchronous mode)
SPDIF: Async (S/P DIF digital signal/Asynchronous mode)
SPDIF: Sync (S/P DIF digital signal/Synchronous mode)
Analog (not assigned digital signal)
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
<When using the D824>
Connect the DIGITAL/DATA IN 1-8 terminal to the OPTICAL OUT (or adat OUT) terminal of the digital device.
If you select [SPDIF: Async] or [SPDIF: Sync] for the digital input, Inputs 1-8 are assigned to track 1 and 2.
If you select [adat: Async] or [adat: Sync] for the digital input, Inputs 1-8 are assigned to tracks 1-8 respectively.
<When using the D1624>
To input an S/P DIF digital signal to the D1624, use the DIGITAL/DATA IN 1-8 terminal. To input adat digital
signal, use the DIGITAL/DATA 1-8 or 9-16 terminal. If you select [SPDIF: Async] or [SPDIF: Sync] for the digital
input, Inputs 1-8 are assigned to tracks 1 and 2. If you select [adat: Async] or [adat: Sync] for the digital input,
Inputs 1-8 are assigned to tracks 1-8 and Inputs 9-16 are assigned to tracks 9-16 respectively.