Fostex D1624 - Manual (Page 114)

114
D824/D1624 Reference Manual (Changing the Initial Settings <SETUP mode>)
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
44.1kHz
SETUP
42 ∞
_
OL
0
8 7 6 5 4 3 2 1
30
24
18
12
9
6
3
16 15 14 13 12 11 10 9
Flashing
Setting digital input
1.While the recorder is stopped, press the SETUP
key to enter SETUP mode.
2.Turn the JOG dial to select [D. in ?] ([?] flashes),
then press the EXECUTE/YES key.
When [D. in?] ([?] flashes) is selected, the presently set
digital input content will be shown.
The flashing [?] is extinguished when the EXECUTE/YES
key is pressed and the digital input setting will change
from lighting to flashing.
In the initial setting, [Analog] will flash as shown below.
3.Select the desired digital signal and digital-in clock
with the JOG dial.
In addition to [Analog], [adat: Async], [adat: Sync],
[SPDIF: Async] or [SPDIF: Sync] can be selected.
[Async]/[Sync] which is displayed together with the
digital signal (S/P DIF or adat) must be selected to
whether the system is to be synchronized or not with
the digital-in clock.
If you do not wish to synchronize the system with digital
in, select [Async] and, if it is to be synchronized, select
[Sync].
4.After selecting, press the EXECUTE/YES key again.
The selected digital signal is registered and [?] in Step-2
will return to flashing.
When the digital input is setup and the correct digital
signal is input, [DIGITAL] will light up in the display.
If set to synchronous mode of [adat: Sync] or [SPDIF:
Sync] and locked to the external digital signal, [EXT SYNC]
will simultaneously light up.
<Notes>
* Should [DIGITAL] flash in the display, check the
connecting cable between the external equipment
and the external equipment setting.
* For the D1624, if the digital input is set to [adat]
(Async or Sync), and if either one of the two DIGITAL/
DATA INPUT (1-8, 9-16) becomes locked, [DIGITAL]
will be lit in the display.
In such a case, the track not locked will automatically
be analog input.
By using this function, 16 track simultaneous
recording can be done by input of analog signals to
tracks 1-8 and adat signals to tracks 9-16.
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
Setting digital output (“D. out ?” menu)
By using the “Setting a digital output” menu, the type of digital signal to be output to external digital equipment
from the DIGITAL/DATA OUT connector (1-8 in D824, 1-8 and 9-16 in D1624) of this recorder, can be setup.
Also, by using this function, sound recorded in this recorder can be sent to external digital equipment (MD,
DAT, adat, digital mixer) in direct digital signals.
• Initial setting: adat
• Assignable digital signal: adat (adat digital signal)
SPDIF (S/P DIF digital signal)
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
<When using the D824>
Connect the DIGITAL/DATA OUT 1-8 terminal to the OPTICAL IN (or adat IN) terminal of the digital device.
If you select [SPDIF] for the digital output, the outputs of tracks 1 and 2 are assigned to OUTPUT 1-8.
If you select [adat] for the digital output, the output of track 1-8 are assigned.
<When using the D1624>
To connect the D1624 with a digital device, to output an S/P DIF digital signal, or to output an adat digital
signal, use the DIGITAL/DATA IN 1-8 or 9-16 terminal. If you select [SPDIF] for the digital output tracks, the
outputs of tracks 1 and 2 are assigned to OUTPUT 1-8 and the outputs of tracks 3 and 4 are assigned to OUTPUT
9-16. If you select [adat] for the digital output, the outputs of tracks 1-8 are assigned to OUTPUT 1-8 and the
outputs of tracks 9-16 to OUTPUT 9-16.