Fostex D1624 - Manual (Page 19)

D824/D1624 Reference Manual (Names and Functions)
19
44.1kHz
SETUP
MTC IN OFFSET
CHASE
LOCATE
PGM REMAIN
FORMAT
SIGNATURE
TEMPO
48kHz
-0.1%
COMPLETED!
SURE?
MIDI CHASE
SAVE LOAD
EXT SYNC
DIGITAL
MTC IN
ABS
42 ∞
_
OL
0
30
24
18
12
9
6
3
8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9
The recorder display integrates the level meter of a high-visibility FL tube with a 16 digits and 35 dot message
display. The level meter shows the Track 1-8 (or 1-16) output level of the recorder section. The time display
shows the current time of the recorder section using ABS TIME (Absolute time), MTC (MIDI time code), or MIDI
BAR/BEAT (bar/beat). This display also shows messages required for interactive operation. The following
section explains the display functions and provides with some examples.
2. Preset Display
The display below shows all preset items for explanation purpose.
Level meter
The level meters shows
the recorder output level
and the recording level
for the tracks.
Tracks 1-8 will function
in the D824 and a D1624
formatted in 96kHz/
24bit, and tracks
functions in D1624
formatted in anything
but 96kHz/24bit.
Track indications
The track indication blinks when the corresponding track is ready. It turns
off when the track is safe, and is lit during recording. Tracks 1-8 will function
in the D824 and a D1624 formatted in 96kHz/24bit, and tracks 1-16 functions
on a D1624 formatted in anything but 96kHz/24bit.
ABS
MTC
SIGNATURE
LOCATE
REMAIN
MTC IN
MTC OFFSET
TC IN
CHASE
PGM
Lights up when ABS is selected as Time base.
Lights up when MTC is selected as Time Base.
Lights up to indicate a bar/beat/clock value when
BAR/BEAT/CLK is selected as Time Base.
Lights up to indicate available recording time and
space on the disk.
With the optional Model 8345 TC/SYNC card
installed, this will be lit when MTC or LTC is
externally input.
Lights up when MTC OFFSET menu is selected
in SETUP mode.
Flashes when "Slave mode" is turned on.
When a signal is locked, the flashing indicator lights
up steadily.
Lights up to indicate the current program number.
Please refer to below.
35 dot message display
This display indicates the ABS time, MTC time value or bar/beat/clock value,
and a parameter name in the SETUP mode.
The name of
the current
drive.
Display section
1. Display shown when the power is turned on
When you turn on the power to the recorder and the connected E-IDE hard disk (a formatted hard disk), the
display shows the [Initializing...] message, [Current Dr], the name of the connected current drive, then recording
mode (Standard format, etc.), and finally the top position of the disk in the time base (ABS, MTC, or BAR/
BEAT/CLK) used in the last Program before you turned the power off.
The following example indicates that the recorder started with the ABS Time Base used in Program 1.
TEMPO
44.1kHz
48kHz
Lights up when the tempo setting menu is selected
in SETUP mode.
This displays the sampling rate of the current drive
disk.
SURE?
This message is shown to confirm whether or not
you wish to execute a certain operation.
COMPLETED!
Format type
and sampling
f r e q u e n c y /
quantization.
44.1kHz
42 ∞
_
OL 0
8 7 6 5 4 3 2 1
30 24 18 12 9 6 3
16 15 14 13 12 11 10 9
42 ∞
_
OL 0
8 7 6 5 4 3 2 1
30 24 18 12 9 6 3
16 15 14 13 12 11 10 9
Lights up when the recorder enters data edit mode,
enabling you to edit data. Pressing the LOCATE
key while this indicate is lit will cause the recorder
to locate the position of the displayed time or the
bar/beat/clock value.
This message indicates that an operation such
as copy, move and paste has been completed.