Please remember this, Press the execute/yes key. (“sure?” flashes.), When inserting an unformatted disk – Fostex D1624 User Manual
Page 93
D824/D1624 Reference Manual (Saving and Loading Song Data)
93
44.1kHz
SETUP
SURE?
SAVE
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
REMAIN
SAVE
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
SAVE
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
SAVE
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
44.1kHz
SETUP
FORMAT
SURE?
SAVE
42
∞
_
OL
0
8
7
6
5
4
3
2
1
30
24
18
12
9
6
3
16
15
14
13
12
11
10
9
* When selecting a program that can be saved on one
backup disk:
The backup disk will indicate that a new program is
going to be created (backup disk shows B01).
Pressing the EXECUTE/YES key will start save
operations and then the following indication will
appear. This indicates that the song data of the
current drive selected is being saved on the B01
backup disk. The disk space necessary to save the
data is counted down while the data is being saved.
When the data is saved, the system goes to the
program time base indication prior to going to the
SETUP mode, then “COMPLETED!” lights up.
* When selecting a program to save that requires
several disks:
Save will immediately start if the EXECUTE/YES
key is pressed at <Step 7>. The save process
appears as in the above case. When the first disk
is full, that disk is ejected and the display will
indicate “Insert second disk !”.
Save is automatically resumed when the second disk
is inserted in the SCSI drive. The same process is
repeated when a third, or more disks are required.
When the program is successfully saved on the last
disk, the program time base indication (ABS 0) that
was started up prior to entering the SETUP mode
appears and “COMPLETED!” lights up.
8.Press the EXECUTE/YES key. (“SURE?” flashes.)
The recorder performs the save operation
differently depending on the selected Program.
<Note>
You cannot interrupt the save operations on the SCSI
harddisk, as with DAT or adat.
You will have to start the save process from the very
first disk again, if you erroneously press the EXIT/NO
key during the insertion of several disks required to
save the program on.
Press the eject switch on the SCSI drive to remove the
disk from the SCSI drive after the program has been
successfully saved.
<Please remember this!>
The instructions on the left was based on use of disks
that were already formatted for backup use, when
saving programs using several disks.
It is recommended that all the disks to save data on are
already formatted prior to the save process. However,
there may be times that you will unexpectedly not have
enough formatted disks during the save process thus,
forcing you to use an “unformatted disk” or a “used
disk” that already has other data saved on it. Observe
the respective procedures described when
inserting the disk according to the [Insert Disk 2] or
[Insert Disk 3] message that prompts you to “Insert
another disk!!” as shown in the instructions on the left.
* When inserting an unformatted disk
The recorder automatically recognizes an
“Unformatted” disk, and will indicate [Unformat!], then
automatically go to the [Disk Format?] menu in the
SETUP mode, to format the backup disk.
Follow the formatting procedures to actually format
the backup disk.
The save process automatically resumes when the disk
is successfully formatted.
* When inserting a disk that is saved or loaded with
other data
The following display may appear as an example,
when inserting such type of disk. This prompt is
asking you whether you want to erase the existing
data saved on the disk that was inserted, and indicates
that you have entered the [Delete PGM?] menu in the
SETUP mode.
If it is okay to erase that disk, press the EXECUTE/YES
key. The [Delete ALL PGM?] message will appear.
Press the EXECUTE/YES key to delete all programs.
Save is automatically resumed after the programs are
deleted. If it is not okay to erase the disk, turn the
JOG dial to select [Eject] when the above indication
appears to eject the disk. Press the EXECUTE/YES key
after [Eject] is selected.
When the disk is ejected, then a prompt to [Insert
Disk] will appear on the display. Insert another disk.
* When inserting a disk that was used as the current
drive
[Wrong Disk] will briefly appear, the [Disk Format?]
menu of the SETUP mode will appear for backup
formatting, then the following indication will appear.
If it is okay to proceed formatting, then execute the
formatting process as done in the above case. If it is
not okay to proceed formatting, then turn the JOG
dial to select [Eject] to eject the disk.
The save operations can automatically be resumed
in such manner when the disk is formatted as a
backup disk or when a program is deleted.