Fostex D1624 - Manual (Page 13)

D824/D1624 Reference Manual (Names and Functions)
13
19. Jog/Shuttle dial
Jog dial (inside):
Turning the JOG dial while the recorder is stopped
performs digital scrubbing in either direction, which
allows you to check the audio and locate a point without
any change in pitch.
The JOG dial is also used to change values in the data
edit mode or when the pitch data is displayed. It also
allows you to select a parameter to set in Setup mode.
Shuttle dial (outside):
FWD and REW direction shuttle operation in the STOP
mode is possible at +/-1 ~ 64times fast winding in the
no sound state. On the other hand, FWD and REW
direction shuttle operation in the PLAY mode is possible
in the CUE playback mode at +1 ~ 8 and -1 ~ -7 times
speed while cueing. In addition, while in the display
edit mode, the editing point can be moved.
* Refer to page “ 54 ” for more information about the
editing the memory data.
* Refer to page “ 101 ” for more information about SETUP
mode.
* Refer to page “ 60 ” for more information about Digital
Scrubbing.
16. Recall key [RECALL]
This is pressed to call out the time figure (or bar/
beat/clk figure) data stored in locate number (0-
99). If the LOCATE key is pressed after pressing this
key, the RECALL LED will light and [Press LOCATE**]
is displayed. Next, by pressing the LOCATE key after
specifying a desired locate number, the time figure
in memory will be recalled into the specified number
and the recorder will enter the edit mode.
Press the LOCATE key to execute this time figure.
* Refer to page " 57 " for more information about using
this key for the Locate operation.
15. Execute/Yes key [EXECUTE/YES]
Press this key to execute the operation when you
edit data on the hard disk using the edit functions
such as Paste and Erase, when you put the recorder
into SETUP mode, or when you set the parameters
in the SETUP menu.
Pressing this key while holding down the SHIFT key
allows you to select the Slave mode on/off.
* Refer to page “ 66 ” for more information about using
this key for the Paste or Erase operation.
* Refer to page “ 101 ” for more information about using
this key in SETUP mode.
* Refer to page " 74 " for more information about using
this key for the Slave Mode operation.
14. Exit key/No key [EXIT/NO]
The opposite of the EXECUTE/YES key, this key is
used to stop operation. When using a removable
type SCSI device for backup, if the "Drive setting" in
the SETUP mode is set to [SCSI6], the SCSI disk can
be ejected by pressing this key while pressing on
the SHIFT key when the SCSI disk is stopped.
* Refer to page “ 66 ” for more information about using
this key for the Paste or Erase operation.
* Refer to page “ 101 ” for more information about using
this key in SETUP mode.
17. NEXT key [NEXT]
If this key is pressed when in the recorder is in the
PLAY/STOP/F FWD or REW mode, locate will be
executed to the next memory point from the present
location point.
When inputting characters in the title edit mode, it
serves as a character short cut function.
The memory number can be advanced with each
press of this key when the recorder displays [Press
LOCATE: **].
18. PREVIOUS key [PREV]
If this key is pressed when the recorder is in the
PLAY/STOP/F FWD or REW mode, locate will be
executed to the one previous memory point.
When inputting character in the title edit mode, this
serves as a character short cut function.
The memory number selecting during display of
[Press LOCATE: **], the memory number can be
reverted with each press of this key.
20. Vari-pitch key [VARI PITCH]
Use this key to turn the Vari-pitch function on and
off. When this function is enabled, the corresponding
LED lights up. When this function is disabled, the
LED turns off. The range of pitch variation for
playback and recording is +/-6.0%, in 0.1% steps.
Press the SHIFT key, and then the VARI PITCH key to
display the current pitch data.
To change the pitch data, use the JOG dial to change
the value while the pitch data is displayed.
You can also change the playback speed when the
data is being played back with the Vari-pitch function
ON. To quit the pitch data display, press the EXIT/
NO key, or the STOP button.
<Notes>
* Even if the pitch data is 0.0% (no speed change),
pressing the VARI PITCH key will still turn on the
VARI PITCH function. The speed is not changed, but
the Vari Pitch is turned on.
* The Vari Pitch function will automatically turn off
under the following conditions:
1. You have turned off and on the power to this recorder.
The pitch data will be reset to 0.0%.
2. You have pressed the EXECUTE/YES key while holding
down the SHIFT key to turn the "SLAVE mode" on (the
setting pitch data remains).
3. You set "Digital In" of the SETUP mode to a SYNC mode
("SPDIF :Sync" or "adat :Sync") and the recorder is
locking to the external clock from DIGITAL IN or WORD
IN. In consequence, [DIGITAL] and [EXT SYNC]
indicators light in the display.
4. You have installed the optional Model 8345 TC/SYNC
card in this recorder and set the LTC OUT to [Gen.].
* Refer to “Quick Operation Guide” for more
information on the Vari-pitch function.
* Refer to pages “ 79 ” and “ 82 ” for more information on
Slave mode.