Fostex D1624 - Manual (Page 129)

129
D824/D1624 Reference Manual (MIDI Implementation Chart/MMC List)
Explanation on the Command/Mode Set
12 22 (<on/off>): loop on/off command
The command for setting the "loop mode on/off" (=ON/OFF of
AUTO RTN) of D824/D1624. Default figure of the loop opera-
tion mode is "12=stop" and this cannot be changed.
12 28 (<post locate mode>): post locate command
The command for setting the "post locate mode" (=ON/OFF of
AUTO PLAY) of D824/D1624. It will stop after locating if "post
locate mode=12." It will enter play after locating if "post locate
mode=15."
12 2D (<on/off>): auto rec command
The command for setting "auto rec mode on/off" (=ON/OFF of
AUTO PUNCH) of D824/D1624. Upon receiving this command,
D-160 will immediately reply the operating condition by send-
ing "32 2D (<edit message>)".
12 41 (<lock enable>): lock enable command
The command for setting "slave mode on/off" (setup menu) of
D824/D1624.
12 42 (<lock mode>): lock mode command
The command for setup of the slave mode (setup menu) when
this equipment is set to "slave mode on."
12 45 (<count><mmc track>) : copy clip command
When this command is received, D-108 will copy (multiple num-
ber of tracks can be copied simultaneously) the sound data, as
data for copy paste, from the pre-registered clipboard-in point
to the clipboard-out point in the track specified by <mmc track>.
With completion of copying the data into the clipboard, D824/
D1624 will immediately reply with "32 45 (<edit message=01
(completed)>)". If copy cannot be executed due to improper
figures of the pre-registered clipboard in/clipboard out points
or incorrect track section, the corresponding <edit message>
will be returned.
12 46 (<count=01><repeat count>): copy paste command
12 46 (<count><repeat count><mmc track>): copy paste com-
mand
When this command is received, D824/D1624 will paste the
sound data which has been copied into the clipboard, on the
same track from the pre-registered auto punch in point as the
starting point for the number of time specified by <repeat
count>.
However, if the sound data length in the clipboard is less than
10ms, the specifying the <repeat count> will be limited to
"01." Also, by specifying <mmc track>, paste can be executed
on other tracks in mono (in one track units) or stereo units (in
combinations of tracks 1-2, 3-4, 5-6, 7-8).
Since time corresponding to length of the copy clipped sound
data is required to complete the copy paste operation, D824/
D1624 immediately replies with "32 46(<edit message=02 (ac-
tive)>)" after receiving the command.
Successively upon completing the paste operation, "32 46 (<edit
message=01(completed)>)" is transmitted.
If paste cannot be executed due to improper figures of the pre-
registered auto punch in point, insufficient disc capacity, no
sound data in the clipboard, etc., the corresponding <edit mes-
sage> will be replied.
12 47 (<count><mmc track>): erase command
When this command is received, D824/D1624 will erase the
data (writes in "0" data) in the section from the pre-registered
auto punch in point through auto punch out point in the track
specified by <mmc track>. Since time corresponding to length
of the erase section is required to complete the erase opera-
tion, D824/D1624 will immediately reply by "32 47 (<edit mes-
sage=02 (active)>)" after receiving the command.
After the completion of erase operation, "32 47 (<edit mes-
sage=01 (completed)>)" will be transmitted.
If erase cannot be executed due to improper figures of the pre-
registered auto punch in point/auto punch out point, incor-
rect track section, etc., the corresponding <edit message> will
be replied.
12 49: clipboard play command
When this command is received, D824/D1624 will playback
once from the head of the sound data copied in the clipboard
by the copy clip and move clip commands.
Immediately after receiving the command, D824/D1624 will
reply with "32 49 (<edit message=02 (active)><count><mmc
track>)." The sound data track number is indicated by (mmc
track>.
Upon completion of playback, "32 49 (<edit message=01 (com-
pleted) is sent and clipboard play is ended. If there is no sound
data in the clipboard, "32 49 (<edit message=14 (void data)>)"
will be sent and clipboard play operation will be interrupted.
12 4A: undo command
Upon receiving this command, D824/D1624 will revert to the
condition prior to editing copy paste,erase, move paste, cut,
redo operation. With completion of undo operation, D824/
D1624 will reply with "32 4A (<edit message=01(completed)>)."
If D824/D1624 is not possible to undo, "32 4A (<edit mes-
sage=00 (no message)>)" will be replied.
12 4B: redo command
When this command is received, D824/D1624 will return to
the condition prior to undo operation.
With completion of redo operation, D824/D1624 will reply
with "32 4B (<edit message=01(completed)>)."
If D824/D1624 is not possible to redo, "32 4B (<edit message=00
(no message)>)" will be replied.
12 4D (<count><mmc track>): move clip command
When this command is received, D824/D1624 will copy (mul-
tiple tracks can be copied simultaneously) the sound data from
the pre-registered clipboard in point to the clipboard out point,
as data for move paste operation. With completion copying
the data into the clipboard, D824/D1624 will immediately re-
ply with "32 4D (<edit message=01 (completed)>)." If copy
cannot be executed by the reason of pre-registered improper
clipboard in/clipboard out point figures or incorrect track sec-
tion, etc., the corresponding <edit message> will be replied.
12 4E (<count=01><repeat count>): move paste command
12 4E (<count><repeat count><mmc track>): move paste com-
mand
When this command is received, D824/D1624 will paste the
sound data which have been move
clipped in the clipboard,
for the number of times specified by <repeat count> on the
same track from the pre-registered auto punch in point as the
starting point. At the same time, the move clipped original