Fostex D1624 - Manual (Page 44)

44
D824/D1624 Reference Manual (Punch In/Out)
Press the foot switch at the
Punch In point.
Track 5
Track 6
Track 7
Track 8
Auto Punch In point
(Take In)
Track 1
Track 2
Track 3
Track 4
This part is changed.
Start point of
playback
Auto Punch Out point
(Take Out)
End point of
playback
All tracks are in
playback monitoring
mode.
Only track 3 in input
monitoring.
The sound is not recorded at
this time. The RECORD
button lamp flashes.
All tracks are in
playback monitoring
mode.
Press the foot switch at the
Punch Out point.
6. When you finish rehearsing, press the STOP
button.
If you are still unsatisfied, repeat steps 3-5.
Cancelling Rehearsal mode
1. While holding down the STOP button, press
the foot switch.
The display shows [Rehearsal Off] for 1 second, then
the flashing REHEARSAL LED turns off and cancels the
rehearsal mode.
<Hint>
To rehearse repeatedly, set the AUTO RTN START point
slightly before the Punch In point, and the AUTO RTN
END point slightly before the Punch Out point.
This will help you concentrate on your performance or
check the recording level easily (especially since Manual
Punch In/Out involves operating the foot switch
operation as well as the recorder). (See <Hint-2> in the
“Rehearsing Auto Punch In/Out recording” for more
information.)
Manual Punch In/Out take
You can proceed to record if you are satisfied with the recording level, foot switch timing, and
rehearsal.
<Note>
You cannot record a second take during the Manual
Punch In/Out operation without stopping the recorder.
That is, the recorder will continue playing after you
finish recording a take, but you cannot record another
take by pressing the foot switch.
Press the foot switch at the
Punch In point.
Track 5
Track 6
Track 7
Track 8
Auto Punch In point
(Take In)
Track 1
Track 2
Track 3
Track 4
This part is changed.
Start point of
playback
Auto Punch Out point
(Take Out)
End point of
playback
All tracks are in
playback monitoring
mode.
Only track 3 in input
monitoring, and data will be
recorded. The RECORD
button lamp flashes.
All tracks are in
playback monitoring
mode.
Press the foot switch at the
Punch Out point.
1. Confirm that Rehearsal mode is cancelled,
and start playing the recorder from a point
slightly before the desired Punch In point.
2. Play the guitar, accompanying the playback
of tracks 1 to 8.
3. Press the foot switch at the desired Punch In
point. Press the foot switch again at the
desired Punch Out point.
The recorder enters recording mode at the Punch In
point, and cancels recording mode at the Punch Out
point.
4. Press the STOP button.
5. Play track 3 and check the result of Punch In/
Out.
<Caution after Punch Out>
At “Take” of punch out, the punch-in recording track
will not immediately enter the repro monitor mode from
the input monitor mode enter the repro monitor mode
about two seconds after mute playback. This is a
functional feature of the recorder and not a malfunction.
<Hint>
You can use the PLAY button and the RECORD
button, instead of using the foot switch.
Follow the steps below.
This method also does not allow you to record
another take unless you stop the recorder first.
Procedure:
1.Press the PLAY button to start playback from a
point slightly before the Punch In point.
2.Press the RECORD button while holding down
the PLAY button at the desired Punch In point.
(Punch In recording starts.)
3.Press the PLAY button at the desired Punch Out
point. (Recording is punched out.)
• If you press only the RECORD button in both
steps 2 and 3, you can rehearse Punch In/Out.