Gilderfluke&Co old Smart Brick Manual - Manual (Page 42)

BYTE 3= SPACE
BYTE 4 & 5 = INPUT STATUS
BIT 0 = GREEN INPUT STATUS (1 = closed)
BIT 1 = BLUE INPUT STATUS (1 = closed)
BIT 2 = PB INPUT STATUS (1 = closed)
BIT 3 = not used
BIT 4 = THUMBWHEEL SWITCH BIT 0
BIT 5 = THUMBWHEEL SWITCH BIT 1
BIT 6 = THUMBWHEEL SWITCH BIT 2
BIT 7 = THUMBWHEEL SWITCH BIT 3
BYTE 6 = SPACE
BYTE 7 & 8 = CURRENT, OR MOST RECENT SHOW NUMBER
BYTE 9 = SPACE
BYTES 10 through 13 = CURRENT BRICK ADDRESS
BYTE 14 = SPACE
BYTE 15 & 16 = DISPLAY HOURS
BYTE 17 = COLON
BYTE 18 & 19 = DISPLAY MINUTES
BYTE 20 = COLON
BYTE 21 & 22 = DISPLAY SECONDS
BYTE 23 = PERIOD
BYTE 24 & 25 = DISPLAY FRAMES
BYTE 26 = SPACE
BYTE 27 & 28 = DIPSWITCH 1
BYTE 29 = SPACE
BYTE 30 & 31 = J-6 PORT
BYTE 32 = CARRIAGE RETURN
BYTE 33 = LINE FEED
EXAMPLE: to poll the status for Brick Brain 00:
i 0 0 82 10 02 039D 02:00:05.08 30 00
This would tell you that the Brick Brain is running an internally clocked show, that the system is cur-
rently cycling shows, that the thumbwheel switch is set to Ф1Х, the show number is Ф02Х, the frame being
addressed in the Smart Bricks is 039D, the time into the show is 5.08 seconds, that record is enabled and
we are using 64K Smart Bricks, and that there is no input to the J-6 port.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒkÓ (track#) Brick Brain Status:
This command responds with the following information for the Brick Brain specified by the TRACK#:
BIT 0 = STORED START RECEIVED
BIT 1 = CYCLING SHOWS FLAG
BIT 2 = DOING DELAY BETWEEN SHOWS
BIT 3 = DOING SHOW END
BIT 4 = LaserDisk CLOCKED SHOW
BIT 5 = EXTERNALLY CLOCKED SHOW
BIT 6 = SMPTE CLOCKED SHOW
BIT 7 = INTERNALLY CLOCKED SHOW
EXAMPLE: to poll the status of the Brick Brain addressed at 00:
k 0 0 40
This would tell you that the Brick Brain is currently running a SMPTE clocked show.
G ILDERFLUKE & C O .¥ 205 S. F LOWER S T .¥ B URBANK , CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485
32 of 134