Gilderfluke&Co old Smart Brick Manual - Manual (Page 43)

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒlÓ (track#) Switch Status:
This command responds with the following information for the Brick Brain specified by the TRACK#:
BIT 0 = GREEN INPUT STATUS (1 = closed)
BIT 1 = BLUE INPUT STATUS (1 = closed)
BIT 2 = PB INPUT STATUS (1 = closed)
BIT 3 = not used
BIT 4 = THUMBWHEEL SWITCH BIT 0
BIT 5 = THUMBWHEEL SWITCH BIT 1
BIT 6 = THUMBWHEEL SWITCH BIT 2
BIT 7 = THUMBWHEEL SWITCH BIT 3
EXAMPLE: to poll the input switch status for Brick Brain 00:
l 0 0 31
This would tell you that the Brick Brain has the thumbwheel switch set to Ф3Х, and that their is an input
present on the GREEN input.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒmÓ (5AA5) (track#) Enter Setup Mode:
This command puts the Brick Brain specified by the TRACK# into the configuration mode. All other
Brick Brains in the system are locked off from receiving any serial commands when there is even one
Brick Brain in configuration mode. They will not accept any serial commands until they hear the com-
mands to exit configuration mode being sent to the one Brick Brain which is in this mode. For details on
the configuration mode, see the configuration section of this manual.
EXAMPLE: to put Brick Brain 00 into setup mode:
m 5 A A 5 0 0
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒnÓ (track#) Memory Address Status:
This command responds with the address being sent to the Smart Bricks by the Brick Brain specified
by the TRACK#. By polling this value, you can monitor the progress of any show.
EXAMPLE: to poll the memory address status for Brick Brain 00:
n 0 0 0000
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒoÓ (track#) Dipsw1 Status:
This command responds with the current status of the dip switch 1 for the Brick Brain specified by the
TRACK#.
EXAMPLE: to poll the dipswitch #1 status for Brick Brain 00:
o 0 0 00
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒqÓ (track#) J-6 Port Status:
This command responds with the current status of the J-6 PORT for the Brick Brain specified by the
TRACK#.
EXAMPLE: to poll the J-6 PORT status for Brick Brain 00:
G ILDERFLUKE & C O .¥ 205 S. F LOWER S T .¥ B URBANK , CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485
33 of 134