Gilderfluke&Co old Smart Brick Manual - Manual (Page 62)

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒgÓ Next Show:
This command is used to select which show will be played next if there were no other higher priority
show requests made. Valid entries are from 00 to 3Fh. 01 through 3Fh select specific shows and any
show number can be used. If the current show requests itself, then it will loop until a different show is re-
quested.
Entering a NEXT SHOW value of 00 is how you tell the Brick Brain that you want it to drop back into
the sequence of shows it had been playing before the last specific show request had been received. As
an example:
Shows 1 through 6 each request the next consecutive show in line
Show 7 requests show number 1 at itÕs end
Show 10 through 16 each request the next consecutive show in line
Show 17 has a Ф00Х entered for the next show at itÕs end
Once started, the shows 1 through 7 will loop for ever
A request comes in for show 10 while playing show 3
Shows 10 through 17 are played
At the end of show 17, the next show played will be show number 4
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒhÓ Immediate:
This toggles the ÔIMMEDIATE CHAIN FLAGÕ for this show. When set, the next show will be played imme-
diately after this show ends as long as the system is currently looping shows. The next show can be a
specifically requested Ônext showÕ, or a return from a specifically requested show if Ф00Х is entered as the
Ônext showÕ. If the ALLOW CHAINS flag is set, then the next show will be played immediately, even if the
system is not currently looping shows. This flag takes precedence over the DELAY FLAG below.
IMMEDIATE CHAINS can be used to build up longer shows from a number of shorter segments. You
might want to do this if you are fixing a error in the show burnt onto a LaserDisk (skipping over a slow part
of the show, for example), or to build up a show which runs continuously between the main shows, but
has a number of ÔseamsÕ where it can branch to another show if one is specifically requested. You can
program the animation at these ÔseamsÕ so that there will be no jumps when the other shows start and
end.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒiÓ Delay:
This toggles the ÔDELAY FLAGÕ for this show. When set, the countdown timer will be started after this
show ends if the system is currently looping shows. What happens at the end of this countdown is up to
what ever the Brick Brain is configured to do at countdown end.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒmÓ More...:
This toggle saves any changes you have made in the currently displayed show, and gets you back
to the main configuration menu.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒxÒ or ÒXÓ eXit Setup Mode:
This command saves any changes you have made in the currently displayed show, and gets you di-
rectly to the exit command on the main configuration menu. When you answer ÔYÕ or ÔNÕ, the screen will
remain unchanged, but you will be out of the configuration mode.
G ILDERFLUKE & C O .¥ 205 S. F LOWER S T .¥ B URBANK , CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485
52 of 134