Gilderfluke&Co old Smart Brick Manual - Manual (Page 46)

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒYÓ (track#) Un-Cock Track:
This command resets the cocked flag on the Brick Brain addressed by the TRACK#. After this flag is
reset, the addressed Brick Brain will no longer respond to COCKED commands.
EXAMPLE: to un-cock Brick Brain 00:
Y 0 0
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒZÓ Un-Cock Global:
This command resets the cocked flag on all the Brick Brains in the system. After the cocked flags are
reset, no Brick Brains in the system will respond to any COCKED commands.
EXAMPLE: to un-cock all Brick Brain in the system:
Z
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
Loop Commands:
Т!У (track#) Loop Track:
ÒÒÓ Loop Global:
Т#У Loop Cocked:
Т$У (group) Loop Group (Rack Smart Brick Brain Only):
These command acts much like a START commands, except that they also set the ÔLOOPING SHOWSÕ
flag. With the this flag set, it is possible to set a sequence of shows playing in any order. The shows can
be played with no delay or with a preset delay between each. Since the ÔnextÕ show can be any show
you ask for, one show can be played over and over again, or you can set up a sequence of shows
which will be repeated until the Brick Brain is told to stop.
When the ÔLOOPING SHOWSÕ flag set, the Brick Brain will check to see if the ÔIMMEDIATE CHAINÕ or
ÔDELAYÕ flags are set when it has finished playing a show. If the show has a the ÔIMMEDIATE CHAINÕ flag
set, then it will immediately start playing the ÔnextÕ show, which you can set to be any show in the sys-
tem. If the ÔDELAYÕ flag is set, then the Brick Brain will check to see if the thumbwheel switch on its front is
set to anything other than 0. If it is, then it will then start this new delay countdown. At the end of the
countdown, whatever ÔCountdown endÕ actions are set will take place just as though a switch closure
input had just happened. In most cases this will be another LOOP command, which will then start the
next show. At the end of that show, the whole process will then start over.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
Stop at End Commands
Т%У (track#) Stop at End Track:
Ò&Ó Stop at End Global:
Т'У Stop at End Cocked:
Т(У (group) Stop at End Group (Rack Smart Brick Brain Only):
These commands reset the cycling mode in the selected Brick Brain(s) . What this dies is to stop them
playing when the end of their current shows are reached. The STOP commands are used when you
want to stop a show immediately. These commands are used when you want the shows to finish grace-
fully.
If the ÔALLOW CHAINSÕ option has been selected on a Brick Brain, then any immediate jumps to what-
ever the next show is will take place even after the cycling mode has been stopped by using these com-
mands
G ILDERFLUKE & C O .¥ 205 S. F LOWER S T .¥ B URBANK , CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485
36 of 134