Rockwell Automation 2706 DL40 HARDWARE USER MANUAL - Manual (Page 169)

Index
Index – 4
RS-232 tape recorder settings,
6 – 12
RS-485 Port
and multiple DL40s, 8 – 2
set to open protocol, 11 – 9
RS-485 port, uses of, 8 – 1
RS-485 port settings, 6 – 12
Run Mode
Message/Variable/Slave,
3 – 2–3 – 5
overview, 3 – 1
Run Modes, 2 – 9–2 – 12
Bit Trigger, 3 – 6–3 – 9
Message List, 3 – 5–3 – 6,
4 – 3–4 – 4
Message/Variable, 3 – 5
Message/Variable/Slave,
4 – 2–4 – 3
overview, 4 – 1
S
Scanner module, 10 – 5
Scroll message, 7 – 8, 7 – 9
Select button enable DIP switch,
12 – 6
Select enable DIP switch, 12 – 12
Send Date to PLC, 5 – 6
Send message time to the stack,
7 – 11
Send message to slave, 7 – 8
RS-485 Port setting, 8 – 1
Send message to the stack, 7 – 11
Send Time to PLC, 5 – 6
Setting the clock, 5 – 4, 5 – 5
Sign bit, BCD, 9 – 5, 10 – 11
Slave address, 10 – 13
Slave devices, 6 – 13
Slave display, 2 – 7
Port settings for, 7 – 9
Special keys, 7 – 3
Special Messages
901 (or 01), 5 – 1
902 (or 02), 5 – 2
903 (or 03), 5 – 2
904 (or 04), 5 – 2
905 (or 05), 5 – 2
906 (or 06), 5 – 2
907 (or 07), 5 – 3
908 (or 08), 5 – 3
909 (or 09), 5 – 4
910 (or 10), 5 – 4
911 (or 11), 5 – 5
912 (or 12), 5 – 6
913 (or 13), 5 – 6
914 (or 14), 5 – 6
915 (or 15), 5 – 7
916 (or 16), 5 – 7
Clear Display and Queue, 5 – 2
Clear Historical Events Stack,
5 – 4
Clear Queue, 5 – 2
Interactive Clock Setting, 5 – 4
Print Historical Events Stack –
Chronological Order, 5 – 2
Print Historical Events Stack –
Frequency of Occurrence,
5 – 3
Reset Unit, 5 – 2
Send Date to PLC, 5 – 6
Send Time to PLC, 5 – 6
Set Clock with Variable Data,
5 – 5
Set Display Intensity, 5 – 7
Stop Special Messages/Resume
Run Mode, 5 – 7
Terminate Message – Clear
Display, 5 – 1
Test Display, 5 – 2
View Display Parameters, 5 – 6
View Historical Events Stack,
5 – 3
Special messages, 2 – 10
table of, 5 – 1
Stack
Historical Event, 6 – 1
Historical Events, 7 – 11
sending message time to, 7 – 11
Special Messages, 5 – 2
Sub-scanner, with PLC 5/15,
10 – 6
T
Table of Special Messages, 5 – 1