Yaskawa E7B Drive Bypass - Manual (Page 18)

Physical Installation 1 - 6
Table 1.4 480V Enclosure Data
Input
Volts
HP 1
Drive
Model
CIMR-
Bypass 2
Model
Number
NEC
FLA
OL
110%
1 min
Heat 3
Loss
Watts
Enclosure Dimensions 4
NEMA 1 & NEMA 12 -FVFF
H W D
inches
Weight 5
of
Assembly
Enclosure Dimensions w/Add-on 4
NEMA 1 & NEMA 12-FVFF
H W D
inches
Weight 5 of
Assembly
+Add-on
Box
Electrical
Schematic
480
0.5 42P21 E7B_B001 1.1 1.2 57
29.48 19.06 13.66
Dimension Drawing 6
S-5512
115 lbs
43.35 19.06 13.66
Dimension Drawing
S-5513
156 lbs
E7B-00
0.75 42P21 E7B_B001 1.6 1.8 57
1 42P21 E7B_B002 2.1 2.3 62
2 42P21 E7B_B003 3.4 3.7 89
3 42P21 E7B_B004 4.8 5.3 121
5 43P71 E7B_B007 7.6 8.4 155
7.5 45P51 E7B_B011 11.0 12.1 217
10 47P51 E7B_B014 14.0 15.4 318
127 lbs 164 lbs
15 49P01 E7B_B021 21.0 23.1 404
20 40111 E7B_B027 27.0 29.7 408
142 lbs 189 lbs 25 40151 E7B_B034 34.0 37.4 485
30 40181 E7B_B040 40.0 44.0 618
40 40241 E7B_B052 52.0 57.2 1040
40.48 25.63 14.66
Dimension Drawing 7
S-5514
203 lbs
55.35 25.63 14.66
Dimension Drawing
S-5515
281 lbs
50 40301 E7B_B065 65.0 71.5 1045
232 lbs
319 lbs 60 40371 E7B_B077 77.0 84.7 1197
75 40451 E7B_B096 96.0 105.6 1357
241 lbs 332 lbs
100 40551 E7B_B124 124.0 136.4 1749
125 40750 E7B_B156 156.0 171.6 2032
84.00 25.63 26.25 8
Dimension Drawing 9
S-5525
943 lbs
NOT REQUIRED
150 40900 E7B_B180 180.0 198.0 2486
200 41100 E7B_B240 240.0 264.0 2955 1240 lbs
250 41600 E7B_B302 302.0 332.2 4225 1352 lbs
300 41850 E7B_B361 361.0 397.1 4425
TBD TBD
350 41850 E7B_B414 414.0 455.4 4451
400 42200 E7B_B477 477.0 524.7 5099
450 42200 E7B_B515 515.0 566.5 5154
500 43000 E7B_B590 590.0 649.0 7329
Note 1: Horsepower rating is based on a standard NEMA B 4-pole motor.
Note 2: The underscore position in these model numbers codes for the enclosure type: V = NEMA1, B = NEMA12 FVFF.
Note 3: Heat loss is the amount of heat dissipated by the drive at full load with all standard options available inside the enclosure. Drive heat sink losses are
included in the heat loss data. Heat loss data is for the enclosure without the add-on enclosure.
Note 4: Height dimension (H) excludes the mounting screw tabs. Depth dimension (D) excludes MCP disconnect handle.
Note 5: This data represents the total weight with all possible standard options. Weight could be less depending on the options specified.
Note 6: All standard options are available in this size enclosure except options E (RFI Filter) and K (5% Output Reactor). Options E and K require the
add-on enclosure.
Note 7: All options are available in this size enclosure except E (RFI Filter), R (3% Line Reactor), and K (5% Output Reactor). Only option E combined with
either option R or option K can be installed in the add-on enclosure. Options R and K together require an increase in the size of the E7 Bypass Enclosure.
Contact the factory if all three options are required. Options D (2 Motor “OR”) or A (2 Motor “AND”) for 75 Hp and 100 Hp, or for 200 Hp and 250 Hp,
require the next size enclosure.
Note 8: Heat sink mounted externally varies the depth dimension depending on the drive size. Depth will not exceed dimension shown.
Note 9: All options are available in this size enclosure except options D (2 Motor “OR”) or A (2 Motor “AND”) for 200 Hp and 250 Hp require the next
size enclosure.