Yaskawa E7B Drive Bypass - Manual (Page 298)

Index - 4
Floating Point Control
(Up/Down Control) ................................................. 6-13
(MOP Increase/Decrease) ...................................... A-12
Forward Run/Stop Command................................. 5-10, A-4
Frequency Detection...................................................... A-15
Frequency, Output
Accuracy ...................................................................C-4
Command Selection ......................................... 5-5, 5-11
Jump .......................................................5-42, 6-21, A-9
Lower Limit .................................................... 5-41, A-9
Max. Output .......................................... 5-45, A-10, C-2
Meter (Analog Monitor) ........................................ A-17
Mid Output ............................................................. A-10
Minimum Output .......................................... 6-17, A-10
Monitor (U1-02)..................................................... A-26
Prohibited ...............................................5-42, 6-21, A-9
Rated ........................................................................C-2
Setting Resolution .....................................................C-4
Setting Signal (Speed Command) .............................C-4
Troubleshooting ...................................................... 6-21
Upper Limit............................................5-41, 6-21, A-9
Frequency Reference (Speed Command)
Analog Input............................... 2-8 to 2-15, A-4, A-16
Bias................................................................ 5-58, A-16
Gain ............................................................... 5-58, A-16
Loss Detection............................................... 5-68, A-21
Lower Limit .................................................... 5-41, A-9
Preset References 1 thru 4......................5-39, 5-54, A-8
Setting Method Selection (MOP).................. 5-79, A-24
Source (b1-01)........................... 1-12, 3-4, 5-2, 5-4, A-4
Terminals........................................... 2-12 to 2-15, 5-63
Upper Limit............................................5-41, 6-21, A-9
Full Load Amps (FLA) .......... 1-4, 4-3, 4-6, 5-50, A-11, B-3
Fuse
Control Power ..................................................1-14, F-4
DC Bus .............................................................. C-4, F-2
Drive Input ................................................................ 1-9
Troubleshooting ........................... 6-2, 6-8, 6-23 to 6-25
FWD Indicator.................................................................. 3-4
G
Gain
Adjustments.................................. 4-6, 5-58, 5-62, A-16
Analog Output............................................... 5-31, A-17
PI Output .................................................................. A-6
PI Square Root ........................................................ 5-37
Proportional..................................................... 5-29, A-5
Gate Drive PCBs
Inspecting ...........................................................7-2, 7-7
Spare Parts......................................................... F-2, F-3
Testing ............................................................6-24, 6-25
Troubleshooting ...............................................6-9, 6-12
Ground Fault Functions.................................5-70, 6-6, A-22
Ground Fault Interrupter (GFI)
Troubleshooting ...................................................... 6-20
Grounding ..............................................2-5, 6-6, 6-19, 7-10
Protection.................................................................. C-4
Shield Wire .................................................... 2-12, 2-14
Terminals .........................................2-2, 2-3, 2-13, 2-15
H
HAND
Mode...................................................... 3-4, 5-55, A-14
Operation ........................................................... 4-8, 4-9
Position ...........................................................1-11, 1-12
Speed Command Source......................... 5-4, 5-12, 5-24
Hardware Protection Parameters ..........................5-73, A-22
Harmonics
And Reactors ...........................................................1-10
Mitigation ......................................................... C-2, C-3
Heat Loss (Rejection) Data.................................... 1-4 to 1-6
Heatsink
Ambient ......................................................... 1-24, 1-25
Fan ........................................................ 5-73, 5-74, 5-81
Parameters .................................. A-15, A-22, A-25
Replacement ............................................... 7-6, 7-7
Test ...................................................................6-25
Maintenance...............................................................7-3
Hex to Decimal Conversion...........................................A-30
High-Slip Braking................................................A-14, A-23
H/O/A (Hand/Off/Auto) Switch .............1-11, 1-12, 4-8, 4-9
And Serial com .........................................................D-1
And Speed Command..............................................5-11
At Start-Up.................................................................4-4
Horsepower
And Model Number........................................ 1-4 to 1-6
And Unit Weight............................................ 1-22, 1-23
Horsepower, Converting to kW .....................................A-25
Humidity ................................................................. 1-24, 7-3
Ambient Operating ................................................... C-4
Hunting Prevention
Parameters ..............................................................A-23
Troubleshooting.......................................................6-20
I
IGBT (Transistor Module)
Inspecting...................................................................7-2
Testing......................................................................6-24
INCREASE Key ..................................................... 3-3, 5-79
Troubleshooting.......................................................6-16
Indicator, Charge............................................. 2-13, 7-9, C-4
Indicating LEDs............................................ 2-13, 3-2 to 3-7
Replacing ...................................................................7-4
Indicators, Mode .................................................... 3-2 to 3-7
Initialization
kWh Monitor ...........................................................5-81
Mode Selection ........................................................5-36
Parameters ............................................... 5-9, 5-10, A-2
User.................................................4-5, 5-3, 5-79, A-24