Siemens Simatic S7-400 - Manual (Page 629)

Index
Index-3
S7-400, M7-400 Programmable Controllers Module Specifications
A5E00069467-07
Communication bus, 2-5
Communication load, Glossary-2
Communication processor, Glossary-2
Comparison point, 5-57, Glossary-3
Compensating box, 5-55, Glossary-3
connecting, 5-56
Compensation
external, 5-55
internal, 5-55, 5-56
Config. index, M7-400, 11-27
Configure, Glossary-3
Configuring error, analog input module, 5-66
Connecting cable, 6-5
plugging in, 7-7
preparing, 7-6
Connecting cable 721, 7-11
Connection
distributed, 7-2
loads/actuators, 13-42
rules, 6-4
Conversion time
analog input channel, 13-44
analog input channels, 5-35
analog output channel, 5-37, 13-45
Converting, analog values, 5-7
CP, Glossary-2
CPU, Glossary-3
CPU 488-4, M7-400
performance features, 11-2
technical specifications, 11-3
CPU 488-5, M7-400
performance features, 11-2
technical specifications, 11-3
CPUs, M7-400, 11-1
expansion socket, 11-14
function elements, 11-4
main memory and interrupt assignment,
11-40
memory card, 11-8
mode selector switch, 11-9
multipoint interface (MPI), 11-15
performance features, 11-2
status and fault LEDs, 11-6
submodule receptacles for interface
submodules, 11-11
suitable submodules, 11-13
technical specifications, 11-3
CSA, 1-4
Current sensors, connecting, 5-47
Cycle time, analog input module, 13-44
D
Data
static, Glossary-3
temporary, Glossary-3
Data block, Glossary-3
Data record, for diagnostic data, B-2
Data record 1
analog input module configuration, A-11
digital output module configuration, A-8
structure for digital input module, A-4
Data records, for parameters, A-2
Date, M7-400, 11-32
Declaration, Glossary-4
Default setting, Glossary-4
Degree of protection, 1-18
IP 20, 1-18
Delay time, M7-400, 11-29
Destination CPU for interrupt, Glossary-4
digital output module, 4-8
Device security, M7-400, 11-30
Diagnostic buffer, Glossary-4
Diagnostic data, Glossary-4
bytes 0 and 1, B-3
data record, B-2
of the analog input modules, B-14
of the digital input modules, B-4
of the digital output modules, B-8
of the SM 421; DI 16 x 24 VDC, B-4
of the SM 421; DI 16 x 24/60 VUC, B-6
of the SM 422; DO 16 x 20-120 VAC/2 A,
B-12
of the SM 422; DO 16 x 20-125 VDC/1.5 A,
B-8
of the SM 422; DO 32 x 24 VDC/0.5 A, B-10
of the SM 431; AI 16 x 16 Bit, B-14
of the SM 431; AI 8 x 16 Bit, B-18
of the SM 431; AI 8 x RTD x 16 Bit, B-16
Diagnostic interrrupt enable
digital input module, 4-7
digital output module, 4-8
Diagnostic interrupt
IF 971-AIO, 13-53
of analog modules, 5-67
of digital modules, 4-13
Diagnostic messages, 4-9, 5-63
of analog input modules, 5-64
of the digital modules, 4-10
reading out, 4-9, 5-63