Conexant – Comtrol AT Commands for SmartACFL User Manual
Page 103
Command Reference Manual
100722A
Conexant
3-83
Table 3-15. Result Code Definitions
Code
Message
Meaning
+F4
+FCERROR
High speed fax data (V.27, V.29, V.33, or V.17) is expected but a V.21 signal is received.
0
OK
A command line has been executed.
1
CONNECT
For X command values specifying no speed reporting, the modem has connected to the line and either the
line speed is 300 bps and line speed is enabled, or the DTE speed is 300 bps and DTE speed reporting is
enabled.
2
RING
An incoming ring signal is detected on the line. What qualifies as a ring signal is determined by country-
dependent parameters, modifiable through ConfigurACE.
When cellular interface is selected, RING indicates that the cellular phone is receiving an receiving an
incoming call.
3
NO CARRIER
Sent when attempting to establish a call if:
1. Ringback is detected and later ceases but no carrier is detected within the period of time determined
by register S7, or
2. No ringback is detected within the period of time determined by register S7.
Also sent when the modem auto-disconnects due to loss of carrier.
For X0, sent for the following conditions:
1. If busy tone detection is enforced, busy or circuit busy has been detected.
2. If dial tone detection is enforced or selected, dial tone has not been detected.
4
ERROR
Sent during an attempt to execute a command line if any of the following conditions occur:
1. The command line contains a syntax error.
2. The modem cannot execute a command contained in the command line, i.e., the command does not
exist or is not supported.
3. A command parameter within the command line is outside the permitted range.
For X0, X1, X2, and X3, this message is sent instead of DELAYED and BLACKLISTED.
5
CONNECT 1200
The modem has connected to the line and either the line speed is 1200 bps and DCE speed reporting is
enabled, or the DTE speed is 1200 bps and DTE speed reporting is enabled.
6
NO DIAL TONE
For X2 and X4, the modem has been instructed to wait for dial tone during dialing but none is received.
When cellular phone interface is selected, indicates that cellular service is not currently available.
7
BUSY
For X3 and X4, if busy tone detection is enforced, the busy (engaged) signal is detected on the line when
the modem is attempting to originate a call.
8
NO ANSWER
The modem is attempting to originate a call if a continuous ringback signal is detected on the line until the
expiration of the timer S7.
9
CONNECT 600
The modem has connected to the line, the DTE speed is 600 bps, and DTE speed reporting is enabled.
10
CONNECT 2400
The modem has connected to the line and either the line speed is 2400 bps and DCE speed reporting is
enabled, or the DTE speed is 2400 bps and DTE speed reporting is enabled.
11
CONNECT 4800
The modem has connected to the line and either the line speed is 4800 bps and DCE speed reporting is
enabled, or the DTE speed is 4800 bps and DTE speed reporting is enabled.
12
CONNECT 9600
The modem has connected to the line and either the line speed is 9600 bps and DCE speed reporting is
enabled, or the DTE speed is 9600 bps and DTE speed reporting is enabled.
13
CONNECT 7200
The modem has connected to the line at 7200 bps and DCE speed reporting is enabled.
14
CONNECT 12000
The modem has connected to the line at 12000 bps and DCE speed reporting is enabled.
15
CONNECT 14400
The modem has connected to the line at 14400 bps and DCE speed reporting is enabled.
16
CONNECT 19200
The modem has connected to the line and either the line speed is 19200 bps and DCE speed reporting is
enabled, or the DTE speed is 19200 bps and DTE speed reporting is enabled.
17
CONNECT 38400
The modem has connected to the line, the DTE speed is 38400 bps, and DTE speed reporting is enabled.
18
CONNECT 57600
The modem has connected to the line, the DTE speed is 57600 bps, and DTE speed reporting is enabled.
19
CONNECT 115200
The modem has connected to the line, the DTE speed is 115200 bps, and DTE speed reporting is enabled.
22
CONNECT
75TX/1200RX
The modem has established a V.23 originate connection and line speed reporting is enabled.
23
CONNECT
1200TX/75RX
The modem has established a V.23 answer connection and line speed reporting is enabled.
24
DELAYED
For X4, sent when a call fails to connect and the number dialed is considered 'delayed' due to country
blacklisting requirements.
32
BLACKLISTED
For X4, sent when a call fails to connect and the number dialed is considered 'blacklisted'.