Comtrol AT Commands for SmartACFL - Manual (Page 168)

Command Reference Manual
7-24 Conexant 100722A
+FPOLL - Indicate Polling Request........................................ 5-15
+FPR - Fixed DTE Rate ......................................................... 4-13
+FPTS: - Receive Page Transfer Status ................................ 5-14
+FPTS: - Transmit Page Transfer Status............................... 5-14
+FPTS= - Page Transfer Status............................................. 5-18
+FREV? - Identify Product Revision......................................... 5-4
+FRH - Receive Data with HDLC Framing ............................... 4-9
+FRM - Receive Data .............................................................. 4-7
+FRS - Receive Silence........................................................... 4-5
+FSPL - Enable Polling.......................................................... 5-11
+FTH - Transmit Data with HDLC Framing .............................. 4-8
+FTM - Transmit Facsimile ...................................................... 4-6
+FTS - Transmit Silence .......................................................... 4-5
+FTSI: - Report the Transmit Station ID................................. 5-13
+GCAP - Request Complete Capabilities List .......................... 3-7
+GCI - Country of Installation................................................... 3-8
+GMI - Request Conexant Identification................................... 3-6
+GMI - Request Manufacturer Identification............................. 3-5
+GMM - Request Model Identification ...................................... 3-6
+GMR - Request Revision Identification .................................. 3-6
+H - Enable/Disable RPI and DTE Speed.............................. 3-53
+IFC - DTE-Modem Local Flow Control ................................. 3-23
+ILRR - DTE-Modem Local Rate Reporting ........................... 3-23
+IPR - Fixed DTE Rate .......................................................... 3-22
+ITF - Transmit Flow Control Thresholds............................... 3-54
+MR - Modulation Reporting Control ...................................... 3-38
+MS - Modulation Selection ................................................... 3-37
+VCID - Caller ID (CID)............................................................ 3-2
+VDR - Distinctive Ring ......................................................... 6-17
+VDT - Control Tone Cadence Reporting .............................. 6-18
+VDX - Speakerphone Duplex Mode ..................................... 6-20
+VGM - Microphone Gain ...................................................... 6-21
+VGR - Voice Gain Receive (Record Gain) ............................. 6-8
+VGS - Speaker Gain ............................................................ 6-21
+VGT - Voice Gain Transmit (Playback Volume) ..................... 6-8
+VIP - Voice Initialize All Parameters....................................... 6-5
+VIT - Voice Inactivity Timer (DTE/Modem)............................. 6-9
+VLS - Analog Source/Destination Selection ......................... 6-10
+VNH - Automatic Hang-up Control ......................................... 6-4
+VPR - Select DTE/Modem Interface Rate ............................ 6-19
+VRA - Ringback Goes Away Timer ...................................... 6-13
+VRID - Caller ID (CID)............................................................ 3-3
+VRN - Ringback Never Appeared Timer .............................. 6-13
+VRX - Start Modem Receive (Record) ................................... 6-5
+VSD - Silence Detection (Quiet and Silence) ....................... 6-14
+VSM - Compression Method Selection ................................ 6-15
+VSP - Speakerphone ON/OFF............................................. 6-20
+VTD - Beep Tone Duration Timer ........................................ 6-16
+VTS - Send Voice Tone(s) ..................................................... 6-6
+VTX - Start Modem Transmit (Playback)................................ 6-8
A
A - Answer ............................................................................. 3-26
B
B - CCITT or Bell ................................................................... 3-40
\B - Transmit Break to Remote .............................................. 3-45
D
D - Dial ...................................................................................3-24
E
E - Command Echo ................................................................3-12
H
H - Disconnect (Hang-Up) ......................................................3-26
I
I - Identification.........................................................................3-5
K
\K - Break Control...................................................................3-46
-K - MNP Extended Services ..................................................3-47
L
L - Speaker Volume................................................................3-27
M
M - Speaker Control ...............................................................3-28
N
\N - Operating Mode .................................................................3-3
O
O - Return to On-Line Data Mode...........................................3-27
P
P - Set Pulse Dial Default .......................................................3-26
–PPD= - Extension Pickup Notification...................................3-33
Q
Q - Quiet Results Codes Control ............................................3-13
S
S - Read/Write S-Parameter...................................................3-64
S0 - Number of Rings to Auto-Answer....................................3-66
S1 - Ring Counter...................................................................3-66
S10 - Lost Carrier To Hang Up Delay .....................................3-67
S11 - DTMF Tone Duration ....................................................3-68
S12 - Escape Prompt Delay (EPD).........................................3-68
S14 - General Bit Mapped Options Status ..............................3-68
S16 - Test Mode Bit Mapped Options Status..........................3-69
S19 - Reserved ......................................................................3-69
S2 - Escape Character ...........................................................3-66
S20 - Reserved ......................................................................3-69
S21 - V.24/General Bit Mapped Options Status......................3-69
S210 – V.34 Symbol Rates ....................................................3-77
S22 - Speaker/Results Bit Mapped Options Status.................3-70
S23 - General Bit Mapped Options Status ..............................3-70
S24 - Sleep Inactivity Timer....................................................3-70
S25 - Delay To DTR Off .........................................................3-70
S26 - RTS to CTS Delay ........................................................3-71
S27 - Bit Mapped Options Status ...........................................3-71
S28 - Bit Mapped Options Status ...........................................3-71
S29 - Flash Dial Modifier Time ...............................................3-72