Comtrol AT Commands for SmartACFL - Manual (Page 4)

Command Reference Manual
iv Conexant 100722A
3.2.1.6 -SMS= - Select Mode ................................................................................................................. 3-4
3.2.1.7 I - Identification........................................................................................................................... 3-5
3.2.1.8 +GMI - Request Manufacturer Identification .............................................................................. 3-5
3.2.1.9 +GMI9 - Request Conexant Identification .................................................................................. 3-6
3.2.1.10 +GMM - Request Model Identification........................................................................................ 3-6
3.2.1.11 +GMR - Request Revision Identification .................................................................................... 3-6
3.2.1.12 +GCAP - Request Complete Capabilities List............................................................................ 3-7
3.2.1.13 +GCI - Country of Installation..................................................................................................... 3-8
3.2.1.14 &F - Restore Factory Configuration (Profile).............................................................................. 3-9
3.2.1.15 &T - Local Analog Loopback Test .............................................................................................. 3-9
3.2.1.16 &Y - Designate a Default Reset Profile ...................................................................................... 3-9
3.2.1.17 &W - Store Current Configuration ............................................................................................ 3-10
3.2.1.18 &Zn=x - Store Telephone Number ........................................................................................... 3-10
3.2.1.19 %7 - Plug and Play Serial Number........................................................................................... 3-10
3.2.1.20 %8 - Plug and Play Vendor ID and Product Number ............................................................... 3-11
3.2.1.21 **- Load Flash Memory ............................................................................................................ 3-11
3.2.2 DTE-Modem Interface commands ........................................................................................................... 3-12
3.2.2.1
E - Command Echo.................................................................................................................. 3-12
3.2.2.2 Q - Quiet Results Codes Control.............................................................................................. 3-13
3.2.2.3 V - Result Code Form .............................................................................................................. 3-13
3.2.2.4 W - Connect Message Control................................................................................................. 3-13
3.2.2.5 X - Extended Result Codes...................................................................................................... 3-14
3.2.2.6 &C - RLSD (DCD) Option......................................................................................................... 3-18
3.2.2.7 &D - DTR Option ...................................................................................................................... 3-18
3.2.2.8 &K - Flow Control ..................................................................................................................... 3-19
3.2.2.9 &M - Asynchronous/Synchronous Mode Selection .................................................................. 3-19
3.2.2.10 &Q - Sync/Async Mode ............................................................................................................ 3-20
3.2.2.11 &R - RTS/CTS Option .............................................................................................................. 3-20
3.2.2.12 &S - DSR Override................................................................................................................... 3-21
3.2.2.13 &X - Select Synchronous Clock Source................................................................................... 3-21
3.2.2.14 +IPR - Fixed DTE Rate ............................................................................................................ 3-22
3.2.2.15 +IFC - DTE-Modem Local Flow Control ................................................................................... 3-23
3.2.2.16 +ILRR - DTE-Modem Local Rate Reporting............................................................................. 3-23
3.2.3 Call Control .............................................................................................................................................. 3-24
3.2.3.1
D - Dial ..................................................................................................................................... 3-24
3.2.3.2 T - Set Tone Dial Default.......................................................................................................... 3-26
3.2.3.3 P - Set Pulse Dial Default......................................................................................................... 3-26
3.2.3.4 A - Answer................................................................................................................................ 3-26
3.2.3.5 H - Disconnect (Hang-Up)........................................................................................................ 3-26
3.2.3.6 O - Return to On-Line Data Mode ............................................................................................ 3-27
3.2.3.7 L - Speaker Volume ................................................................................................................. 3-27
3.2.3.8 M - Speaker Control ................................................................................................................. 3-28
3.2.3.9 &G - Select Guard Tone........................................................................................................... 3-28
3.2.3.10 &P - Select Pulse Dial Make/Break Ratio ................................................................................ 3-29
3.2.3.11 &V - Display Current Configuration and Stored Profiles .......................................................... 3-29
3.2.3.12 &V1 - Display Last Connection Statistics ................................................................................. 3-30
3.2.3.13 \V - Single Line Connect Message Enable............................................................................... 3-31
3.2.3.14 %L - Report Line Signal Level.................................................................................................. 3-31
3.2.3.15 %Q - Report Line Signal Quality .............................................................................................. 3-32
3.2.3.16 *B - Display Blacklisted Numbers............................................................................................. 3-32
3.2.3.17 *D - Display Delayed Numbers ................................................................................................ 3-32
3.2.3.18 –PPD= - Extension Pickup Notification through 16550 UART ................................................. 3-33
3.2.3.19 –STE= - Set Telephony Extension ........................................................................................... 3-33
3.2.4 Modulation Control Commands................................................................................................................ 3-37
3.2.4.1
+MS - Modulation Selection ..................................................................................................... 3-37
3.2.4.2 +MR - Modulation Reporting Control........................................................................................ 3-38
3.2.4.3 %E - Enable/Disable Line Quality Monitor and Auto-Retrain or Fallback/Fall Forward............ 3-39
3.2.4.4 %U - Select µ-Law or A-Law Codec Type................................................................................ 3-40
3.2.4.5 B - CCITT or Bell...................................................................................................................... 3-40