Comtrol AT Commands for SmartACFL - Manual (Page 167)

Command Reference Manual
100722A Conexant 7-23
7. INDEX
#
#UD – Last Call Status Report ............................................... 3-55
$
$F – FastConnect Control...................................................... 3-63
%
%7 - Plug and Play Serial Number......................................... 3-10
%8 - Plug and Play Vendor ID and Product Number.............. 3-11
%C - Enable/Disable Data Compression................................ 3-49
%E - Enable/Disable Line Quality Monitor.............................. 3-39
%L - Report Line Signal Level................................................ 3-31
%Q - Report Line Signal Quality ............................................ 3-32
%U - Select µ-Law or A-Law Codec Type .............................. 3-40
&
&C - RLSD (DCD) Option....................................................... 3-18
&D - DTR Option.................................................................... 3-18
&F - Restore Factory Configuration.......................................... 3-9
&G - Select Guard Tone ........................................................ 3-28
&K - Flow Control................................................................... 3-19
&L - Leased Line Operation ................................................... 3-62
&M - Asynchronous/Synchronous Mode Selection................. 3-19
&P - Select Pulse Dial Make/Break Ratio............................... 3-29
&Q - Sync/Async Mode.......................................................... 3-20
&R - RTS/CTS Option............................................................ 3-20
&S - DSR Override................................................................. 3-21
&T - Local Analog Loopback Test ............................................ 3-9
&V - Display Current Configuration ........................................ 3-29
&V1 - Display Last Connection Statistics ............................... 3-30
&W - Store Current Configuration .......................................... 3-10
&X - Select Synchronous Clock Source ................................. 3-21
&Y - Designate a Default Reset Profile .................................... 3-9
&Zn=x - Store Telephone Number ......................................... 3-10
)
)M - Enable Cellular Power Level Adjustment ........................ 3-62
*
**- Load Flash Memory .......................................................... 3-11
*B - Display Blacklisted Numbers........................................... 3-32
*D - Display Delayed Numbers............................................... 3-32
:
:E - Compromise Equalizer Enable Command....................... 3-63
@
@M - Initial Cellular Power Level Setting ............................... 3-62
^
^C2 - Download Cellular Phone Driver ................................... 3-78
^I - Identify Cellular Phone Driver........................................... 3-78
^T6 - Indicate Status of Cellular Phone .................................. 3-79
+
+A8E - V.8 and V.8bis Operation Controls .............................3-50
+A8I: - CI Signal Indication.....................................................3-51
+DR - Data Compression Reporting .......................................3-48
+DS - Data Compression........................................................3-47
+EB - Break Handling in Error Control Operation....................3-42
+EFCS - 32-bit Frame Check Sequence ................................3-43
+ER - Error Control Reporting ................................................3-44
+ES - Error Control and Sync Mode Selection........................3-41
+ESA - Configure Synchronous Access Submode .................3-52
+ESR - Selective Repeat........................................................3-43
+ETBM - Call Termination Buffer Management ......................3-45
+FAA - Answer Parameter......................................................5-19
+FAA - Auto Answer Enable.....................................................4-4
+FAE - Auto Answer Enable.....................................................4-4
+FAR - Adaptive Reception Control........................................4-10
+FAXERR - T.30 Session Error Report ..................................5-19
+FBOR - Data Bit Order .........................................................5-19
+FBUF? - Buffer Size .............................................................5-20
+FCFR - Indicate Confirmation to Receive .............................5-13
+FCIG - Set Polling ID............................................................5-11
+FCIG: - Report the Polled Station ID ....................................5-15
+FCL - Carrier Loss Timeout ..................................................4-10
+FCLASS- Select Active Service Class....................................3-2
+FCLASS=1 - Select Facsimile Class 1 Mode..........................4-4
+FCLASS=1.0 - Select Facsimile Class 1.0 Mode....................4-4
+FCLASS=2 - Select Facsimile Class 2 Mode..........................5-1
+FCLASS=8 - Select Voice Mode ............................................6-4
+FCON - Facsimile Connection Response .............................5-13
+FCQ - Copy Quality Checking ..............................................5-18
+FCR - Capability to Receive .................................................5-18
+FCSI: - Report the Called Station ID.....................................5-13
+FDCC - DCE Capabilities Parameters ..................................5-16
+FDCS - Current Session Results Parameters.......................5-17
+FDCS: - Report Current Session Capabilities .......................5-13
+FDD - Double Escape Character Replacement ....................4-10
+FDIS - Current Sessions Capabilities Parameters ................5-16
+FDIS: - Report Remote Station Capabilities .........................5-13
+FDR - Begin or Continue Phase C Receive Data....................5-9
+FDT - Data Transmission .......................................................5-6
+FDTC: - Report the Polled Station Capabilities.....................5-15
+FET - Transmit Page Punctuation ..........................................5-8
+FET: - Post Page Message Response..................................5-14
+FHNG: - Call Termination with Status...................................5-14
+FIT - DTE Inactivity Timeout.................................................4-12
+FK - Session Termination.....................................................5-10
+FLID= - Local ID String.........................................................5-18
+FLO - Flow Control ...............................................................4-14
+FLPL - Indicate a Document for Polling ................................5-11
+FMDL? - Identify Product Model .............................................5-4
+FMFR? - Request Manufacturer Identification ........................5-4
+FMI? - Request Manufacturer Identification ..........................4-13
+FMM? - Request Model Identification ...................................4-13
+FMR? - Request Revision Identification................................4-14
+FPHCTO - DTE Phase C Response Time-out......................5-18