ROTEL RSP-1098 - Manual (Page 27)

27 English
Manual settings available from the front panel
and/or the remote might be used when you
want to play:
• Standard 2-channel stereo (left/right speak-
ers only) with no surround processing
• Downmixed 2-channel playback of Dolby
Digital 5.1 or DTS recordings
• Dolby 3-channel stereo (left/right/center)
of 2-channel recordings.
• 5-channel or 7-channel stereo from 2-chan-
nel recordings
• One of four MUSIC modes for DSP con-
cert hall simulation from 2-channel record-
ings
• Dolby Pro Logic II cinema or music mode
matrix decoding of 2-channel recordings
• DTS Neo:6 cinema or music mode matrix
decoding of 2-channel recordings
• Dolby Digital Surround EX decoding of
Dolby Digital 5.1 channel recordings or
Dolby Digital Surround EX discs that do not
trigger automatic decoding.
NOTE : DTS, DTS-ES Matrix 6.1, DTS-ES Dis-
crete 6.1, DTS 96/24, Dolby Digital, MP3,
MPEG Multichannel, HDCD (96kHz), and
PCM 2-channel (96kHz) digital signals are
auto-detected and cannot be overridden.
However, you can choose to use Dolby Digi-
tal Surround EX decoding for any Dolby Digi-
tal 5.1 source material. You can also downmix
Dolby Digital 5.1 or DTS 5.1 recordings for
2-channel playback.
• HDCD (non 96kHz) and PCM 2-channel
(non 96kHz) digital signals can be over-
ridden to Dolby Pro Logic II, Dolby 3-Ste-
reo, DTS Neo:6, Music 1 – 4, 5CH Ste-
reo, 7CH Stereo, and Stereo.
• Dolby Digital 2-channel Stereo can be over-
ridden to Dolby Pro Logic II, Dolby 3-Ste-
reo, and Stereo.
The following topics describe in detail the
manual surround mode options available for
each type of recording
Dolby Digital 5.1
Dolby Digital Surround EX
Dolby Digital decoding is auto-detected and
cannot be overridden. You may, however, select
a 2 channel downmix of 5.1 channel record-
ings. If the system is configured with center
back speaker(s), you can also force Dolby Sur-
round EX processing on or off.
NOTE : In addition to the options that follow,
you can press the 2CH button on the remote
to toggle between 2-channel downmix and
multichannel playback.
• On a 5.1 system. Press the SUR+ but-
ton on the remote, then press the +/– but-
tons to change between DD 5.1 channel
or DD 2.0 channel downmix playback. On
the front panel, press the MODE button
once, then rotate the FUNCTION knob to
select 2.0 or 5.1 channel playback.
• On a 6.1/7.1 system with a Dolby
Digital 5.1 disc. Press the SUR+ button
on the remote, then use the +/– buttons to
step through four options: DD 5.1 chan-
nel, DD 2.0 channel downmix, DD Surround
EX center back processing, or DD with Rotel
XS center back processing. On the front
panel, press the MODE button while playing
a Dolby Digital source. Then, rotate the
FUNCTION knob to step through the same
options. You should force Surround EX on
for non-flagged discs that are labeled Dolby
Digital Surround EX. Rotel XS processing
of standard 5.1 channel discs will provide
a more diffuse surround effect than the more
highly localized Dolby EX decoding and
will probably be the best 6.1 channel option
for non-Surround EX discs.
• On a 6.1/7.1 system with a Dolby
Digital Surround EX disc. Press the
SUR+ button on the remote, then use the
+/– buttons to step through three options:
DD 5.1 channel, DD 2.0 channel down-
mix, or Surround EX center back process-
ing. On the front panel, press the MODE
button while playing a Dolby Digital source.
Then, rotate the FUNCTION knob to step
through the same options. Select the Sur-
round EX option for 6.1 channel playback.
Select the DD 5.1 option to force Surround
EX off for standard 5.1 channel playback.
NOTE
: When playing any Dolby Digital source,
you can select one of three dynamic range
control settings. See the Dynamic Range topic
in the Other Settings section of this manual.
Dolby Digital 2.0
Dolby Digital decoding is auto-detected and
cannot be overridden. You may, however, select
a 2-channel playback, Pro Logic II matrix sur-
round, or Dolby 3-Stereo playback.
• To select 2-channel stereo, Pro Logic
II, or 3-Stereo. Repeatedly press the
SUR+ button on the remote until the desired
mode is displayed. On the front panel, press
the MODE button once, then rotate the
FUNCTION knob to select the desired
mode.
NOTE
: You can also direct select 2-channel
stereo or Pro Logic II Cinema modes by press-
ing the 2CH or PLC buttons on the remote.
• To select Cinema, Music, or Emula-
tion option in Pro Logic II mode. Press
the +/– buttons on the remote to select the
desired option. On the front panel, press
the MODE button twice while in Pro Logic
II mode. Then, rotate the FUNCTION knob
to select the option.
NOTE : When playing any Dolby Digital source,
you can select one of three dynamic range
control settings. See the Dynamic Range topic
in the Other Settings section of this manual.
DTS 5.1
DTS 96/24
DTS-ES 6.1
DTS decoding is auto-detected and cannot be
overridden. You may, however, select a 2
channel downmix of 5.1 channel recordings
or add Rotel XS center back processing for
5.1 channel discs.
NOTE
: In addition to the options that follow,
you can press the 2CH button on the remote
to toggle between 2-channel downmix and
multichannel playback.
• On a 5.1 system. Press the SUR+ but-
ton on the remote, then press the +/– but-
tons to change between DTS 5.1 channel
or DTS 2.0 channel downmix playback.
On the front panel, press the MODE but-
ton once, then rotate the FUNCTION knob
to select 2.0 or 5.1 channel playback.
• On a 6.1/7.1 system with a DTS 5.1
or DTS 96/24 disc. Press the SUR+ button
on the remote, then use the +/– buttons to
step through three options: DTS 5.1 chan-
nel, DTS 2.0 channel downmix, or DTS with