Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications - Manual (Page 383)

B.3 Parameter Table
YASKAWA ELECTRIC SIEP YAIL1E 01A YASKAWA AC Drive L1000E Technical Manual 383
Pa
ra
met
er
L
is
t
B
14 Fault Reset
Closed: Resets faults if the cause is cleared and the Up/Down command is removed.
194
15 Fast Stop (N.O.)
Closed: Decelerates to stop at the Fast Stop ramp set to C1-09.
194
16 Motor 2 Selection
Open: Motor 1(E1-††, E3-††)
Closed: Motor 2 (E2-††, E4-††)
195
17 Fast Stop (N.C.)
Open: Decelerates to stop at the Fast Stop ramp set to C1-09.
194
18 Timer Function Input
Triggers the timer set up by parameters b4-01 and b4-02. Must be set in conjunction with the timer function output
(H2-†† = 12).
195
1A Accel/decel Ramp Selection 2
Used in conjunction with an input terminal set for “Accel/decel ramp selection 1” (H1-†† = 7), and allows the
drive to switch between accel/decel ramp 3 and 4.
195
20 to 2F External Fault
20: N.O., Always detected, ramp to stop
21: N.C., Always detected, ramp to stop
22: N.O., During run, ramp to stop
23: N.C., During run, ramp to stop
24: N.O., Always detected, coast to stop
25: N.C., Always detected, coast to stop
26: N.O., During run, coast to stop
27: N.C., During run, coast to stop
28: N.O., Always detected, Fast Stop
29: N.C., Always detected, Fast Stop
2A: N.O., During run, Fast Stop
2B: N.C., During run, Fast Stop
2C: N.O., Always detected, alarm only (continue running)
2D: N.C., Always detected, alarm only (continue running)
2E: N.O., During run, alarm only (continue running)
2F: N.C., During run, alarm only (continue running)
196
50 Nominal Speed
Closed: Activates the nominal speed (d1-19).
196
51 Intermediate Speed
Closed: Activates the Intermediate Speed (d1-20).
196
52 Releveling Speed
Closed: Activates the Releveling Speed (d1-23).
196
53 Leveling Speed
Closed: Activates the Leveling Speed (d1-26).
197
54 Inspection Operation
Closed: Activates Inspection operation using the speed set in d1-24.
197
55 Rescue Operation
Closed: Activates rescue operation.
197
56 Motor Contactor Feedback
Used for motor contactor supervision and fault detection.
197
57 High Speed Limit (Up)
Closed: Uses the leveling speed as the maximum speed when going up.
197
58 High Speed Limit (Down)
Closed: Uses the leveling speed as the maximum speed when going down.
197
5A Motor Contactor Feedback 2
Open: Motor contactor closed (N.C.) <1>
Closed: Motor contactor open
197
5B Brake Feedback 2
Open: Brake open (N.C.) <2>
Closed: Brake closed
197
H1 Multi-Function Digital Input Settings
H1-††
Setting
Function Description Page
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_