Roland V-8HD HDMI Video Switcher and UVC-01 USB Capture Device Kit - Manual (Page 75)

75
Menu List
8: AUDIO INPUT
HDMI IN 1–8, AUDIO INPUT
Menu item Value
(Bold: default)
Explanation
INPUT LEVEL -INF– 0.0 –10.0dB Adjusts the input volume.
INPUT MUTE OFF , ON Turns the mute function on/off. If this is “ON”, the input audio is temporarily silenced.
MONO
Converts the input audio from stereo to mono.
OFF Sends the stereo input audio without change.
L ONLY The audio of the L channel is sent to both L and R.
R ONLY The audio of the R channel is sent to both L and R.
LR MIX The audio of the L channel and R channel is mixed, and sent to both L and R.
SOLO OFF , ON
Turns the solo function on/off. Only the audio for which this is “ON” is heard in the
headphones.
* The solo function applies to the headphone output. It does not affect output other
than the headphones.
EFFECT PRESET
Specifies an effect preset (high-pass filter, compressor, equalizer).
* When you change a preset, the settings of each effect are overwritten.
DEFAULT For line input (default setting)
MEETING For meetings
INTERVIEW For interviews
AMBIENT MIC For capturing ambient sound
WINDY FIELD For capturing ambient sound in a windy area
DE-ESS & POPS SOFT For reducing sibilants
DE-ESS & POPS HARD For reducing plosives
DELAY
0.0 –500.0msec
( 0.0 –29.9/25.0frame)
Adjusts the delay time of the audio.
Effect This outputs audio with a delay.
HIGH PASS FILTER 75Hz OFF , ON
Turns the high-pass filter on/off.
Effect Cuts off unneeded low-band audio. The cutoff frequency is 75 Hz.
NOISE GATE OFF , ON
Turns the noise gate on/off.
Effect This mutes audio that is below a specified level.
THRESHOLD -80.0– -50.0 –0.0dB
Specifies the level used as the threshold for removing audio. Audio below the level set
here is removed.
RELEASE 30– 380 –5000ms
Adjusts the length of time until the audio is fully attenuated after audio falls below
the threshold.
COMPRESSOR OFF , ON
Turns the compressor on/off.
Effect This compresses audio that exceeds a specified level.
THRESHOLD -80.0– -50.0 –0.0dB
Specifies the level used as the threshold at which the compressor is applied.
Compression is applied to audio that exceeds the threshold.
RATIO
1.00: 1, 1.12: 1, 1.25: 1, 1.40: 1,
1.60: 1, 1.80: 1, 2.00: 1, 2.50: 1,
3.20: 1, 4.00: 1,
5.60 : 1 , 8.00: 1,
16.0: 1, INF: 1
Specifies the degree of compression applied to the audio. The state in which no
compression is applied is defined as “1”.
ATTACK 0.2– 1 –100ms Specifies the time until compression starts when audio exceeding the threshold is input.
RELEASE 30– 380 –5000ms
Adjusts the length of time until compression ends after audio falls below the
threshold.
AUTO GAIN OFF, ON
Turns the auto makeup gain feature on/off.
If this is “ON”, the final output volume level after applying the compressor is
automatically adjusted according to the “THRESHOLD” and “RATIO” settings.
The total of the “MAKEUP GAIN” setting value described below and the value
calculated by auto makeup gain becomes the final output volume level
(up to +34 dB).
MAKEUP GAIN -40– 0 –40dB Adjusts the final output volume after applying the compressor.
EQUALIZER OFF , ON
Turns the equalizer on/off.
Effect Adjusts the tone for each frequency band.
Hi GAIN -15.0– 0.0 –15.0dB Boosts or attenuates the high band.
Hi FREQUENCY 1.0– 10.0 –20.0kHz Specifies the center frequency when changing the tone in the high band.
Mid GAIN -15.0– 0.0 –15.0dB Boosts or attenuates the middle band.