Konica Minolta bizhub PRESS C8000e - Manual (Page 325)

bizhub PRESS C8000 10-17
10.1 Utility Menu Screen Outlines 10
[05 Glue Finish Position]
Adjust the position to finish gluing on
the body set. The sizes referred to in
this section are those of body sets cor-
responding to cover sizes. Objects of adjustment:
Ahead (rear): Full Area, A4
v, B5 v, A5
w/v, 8.5 e 11 v, 5.5 e 8.5 w, 16K v, Cus-
tom (220-379 mm), Custom (148-219 mm)
Back (front): Full Area, A4
v, B5 v, A5 w/v,
8.5 e 11 v, 5.5 e 8.5 w, 16K v, Custom
(220-379 mm), Custom (148-219 mm)
Adjustable range:
-128 (Soon) to +127 (Late)
(1 step = 0.1 mm)
*
[06 Temperature Adjustment]
Glue Tank -Top*:
The machine supplies glue pellets on
detecting the temperature of solution
surface lower than the set point. It is
recommended to be set higher in ther-
mal environment where the machine
tends to fail in detection.
Glue Tank -Mid*:
Set the temperature to reach when
warm-up is completed, and to start ro-
tating the roller. Setting it higher helps
glue temperature to be stable sooner.
Glue Tank -Low:
Adjust the temperature to control the
tank heater.
Low temperature: increases glue vis-
cosity High temperature: decreases
glue viscosity
Glue Apply Roller:
Adjust the temperature to control the
roller heater. This also supports heat-
ing of the glue.
Low temperature: increases glue vis-
cosity High temperature: decreases
glue viscosity
*: Temperature setting cannot be made
for Glue Tank -Top and Glue Tank -Mid
by default. Contact your service repre-
sentative, if desired. Glue Tank -Top:
Initial: 132°C
Recommended: 128 to 136°C
Glue Tank -Mid:
Initial: 145°C
Recommended: 140 to 145°C
Glue Tank -Low:
Initial: 185°C
Recommended: 180 to 190°C
Glue Apply Roller:
Initial: 165°C
Recommended: 160 to 170°C
(1 step = 0.1°C) *
[07 Sub Compile CD Width Adj.]
Change the adjustment width if output
sheets cannot be aligned in sub com-
pile section. The sizes referred to in this
section are those of body sets corre-
sponding to cover sizes. Objects of adjustment:
Full Area, A4
v, B5 v, A5 w/v, 8.5 e 11 v,
5.5
e 8.5 w, 16K v, Custom (220-379 mm),
Custom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
*
[08 Clamp CD Width Adjustment]
Change the adjustment width in cross-
wise direction if output sheets show
misalignment in a body set. The sizes
referred to in this section are those of
body sets corresponding to cover siz-
es. Objects of adjustment:
Full Area, A4
v, B5 v, A5 w/v, 8.5 e 11 v,
5.5 e 8.5 w, 16K v, Custom (220-379 mm),
Custom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
*
[09 Cover Up/Down CD Width Adj.]
Change the adjustment width in
matching body sets and covers, in or-
der to adjust their positions in cross-
wise direction. Objects of adjustment:
Perfect Binder Tray, Except PB Tray
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm) *
[10 Clamp FD Position Adj.]
Change the adjustment width in paper
feed direction if output sheets show
misalignment in a body set. The sizes
referred to in this section are those of
body sets corresponding to cover siz-
es. Objects of adjustment:
Full Area, A4
v, B5 v, A5 w/v, 8.5 e 11 v,
5.5 e 8.5 v, 16K v, Custom (220-379 mm),
Custom (148-219 mm)
Adjustable range:
-20 (Wide) to +20 (Narrow)
(1 step = 0.1 mm)
*
Menu Item/Description Setting options (with default bolded)