Rockwell Automation 1775-S5_SR5,D17756.5.5 User Manual PLC-3 FAMILY I/0 - Manual (Page 28)

Configuring the Scanner through LIST
Chapter 2
2-2
The heading for this menu shows the scanner’s thumbwheel setting and
slot location in the processor chassis. Selections 6 and 7 only display for
scanner number 1. We describe these selections in the rest of this chapter.
Figure 2.1
LIST Selections for the Scanner
SystemĆMode
1 Test Monitor
2 Run Monitor
3 Program Load
4 Remote Enable
5 System Status
6 Module Status
Enter Next > 6 Modules
1 01 1775ĆME
2 01 1775ĆL3
3 01 1775ĆS5
Enter Next > 3 1775ĆS5 1
Chass 1 Slot 3
1 Channel 1
2 Channel 2
3 Channel 3
4 Channel 4
5 Rack Range
6 Chan 0
7 Display
Enter Next >
S5 1ĆChan 1
1 Baud *57.6 115.2 230.4
2 Mode: I/O
3 Auto Config
4 Reconfiglkp
5 I/O Scan Config
6 Peer Master Config
7 Peer Slave Config
8 Backup Comm. Config
Enter Next >
S5 1ĆChan 4
1 Baud *57.6 115.2 230.4
2 Mode: I/O
3 Auto Config
4 Reconfig
5 I/O Scan Config
6 Peer Master Config
7 Peer Slave Config
8 Backup Config
9 DH/DH+ Config
Enter Next >
S5 1
1* 0Ć76
2 100Ć176
3 200Ć276
4 300Ć376
Enter Next >
S5 1 Chan 0
1 l.T Defaults
2 Privileges
3 Baud
4 Parity *Even Odd None
5 Stopbits *1 1.5 2
6 Chan Timeout 10000 ms
7 Reconfig
Enter Next >
Front Display Privileges
3
10
67
69
70
Enter Next >
Mode Selection
1 Inactive
2* I/O
3 Peer Master
4 Peer Slave
5 Backup Comm
Enter NExt >
Mode Selection
1 Inactive
2* I/O
3 Peer Master
4 Peer Slave
5 Backup Comm
6 DH
7 DH+
Enter NExt >
Chan 0ĆPrivileges
0
2
3
4
5
6
8
10
64
65
66
68
69
70
71
72
Enter Next >
S5 1. Chan 0 Baud
1 110 Baud
2 150 Baud
3 300 Baud
4 600 Baud
5 1200 Baud
6 1800 Baud
7 2400 Baud
8 4800 Baud
9* 9600 Baud
10 19200 Baud
Enter Timeout >
S5 Chan 1 I/O
1 003/2/0
2 005/2/2
3 006/2/6/I
4 003/2/2
5 005/4/4/I/F
Enter Next >
S5 Chan 1 Peer Master
1 Master 1
2 Slaves
Enter Next >
S5 Chan 1 Peer Slave
1 Slave 1
2 Master 1
3 Input File I1:0 → 50
4 Output File O1:0 → 20
Enter Next >
S5 Chan 1 Backup Comm
1 Resident 1
2 Partner 2
3 Input File I1:0 → 50
4 Output File O1:0 → 20
Enter Next >
S5 1 Chan 4
1 Node Mode * OnĆline OffĆline
2 Station Number: 030 Selected 030 Actual
3 DH/DH+ Timeouts
4 Backup Operation
5* Send Unprotected
6* Accept Upload/Download
7* Accept Writes
8 Input File List
9 Privileges
10 DH/DH+ Switch Settings
11 DH+ Active Node List
12 DH+ Active Nodes To Status File 6
Enter Next >
Enter Master >
S5 Chan 1 Slaves
Slave 86
Slave 82
Slave 84
Enter Next >
Enter Slave >
Enter Master >
Enter Input File >
Enter Output File >
Enter Resident >
Enter Partner >
Enter Input File >
Enter Output File >
Enter Station Number
(Enter Leading 0 For
Octal Number) >
S5 1
DH/DH+ Timeouts
1 Outgoing Message 5.0 Sec
2 List Channel 300.0 Sec
3 Remote Program 300.0 Sec
Enter Next >
Privileges
0
3
4
5
6
8
10
64
65
66
68
69
70
71
72
74
Enter
Next >
The asterisk (*) indicates the default selection
See page 2Ć16
See page 2Ć19 & 2Ć20
S5 Chan 1 Slave 86
1 Input File I1:0 → 20 → Enter Input File>
2 Output File O1:0 → 20 → Enter Output File>