Hypertherm HT4001 Plasma Arc Cutting System - Manual (Page 111)

HT4001 with Slave –
Cut Chart and Consumable Parts Index
Consum. Retaining Swirl
Type Metal Amps Plasma Gas Cap Nozzle Ring Electrode Page
260 Nitrogen 020580 020281 020039 020285 5-29
400 Nitrogen 020580 020282 020039 020285 5-29
600 Nitrogen 020580 020283 020039 020285 5-29
760 Nitrogen 020580 020284 020040 020285 5-29
260 Nitrogen 020580 020281 020039 020285 5-30
400 Nitrogen 020580 020282 020039 020285 5-30
600 Nitrogen 020580 020283 020039 020285 5-30
760 Nitrogen 020580 020284 020040 020285 5-30
260 Nitrogen 120390 120386 020039 020968 5-31
400 Nitrogen 120390 120387 020039 020968 5-31
600 Nitrogen 120390 120388 020039 020968 5-31
760 Nitrogen 120390 120389 020040 020968 5-31
260 Nitrogen 120390 120386 020039 020968 5-32
400 Nitrogen 120390 120387 020039 020968 5-32
600 Nitrogen 120390 120388 020039 020968 5-32
760 Nitrogen 120390 120389 020040 020968 5-32
OPERATION
1-99
5-20
HT4001
Instruction Manual
HT4001 without Slave –
Cut Chart and Consumable Parts Index
Consum. Retaining Swirl
Type Metal Amps Plasma Gas Cap Nozzle Ring Electrode Page
260 Oxygen 020579 020086 020623 020663 5-21
340 Oxygen 020579 020086 120135 120630 5-21
260 Nitrogen 020579 020089 020039 020082 5-22
400 Nitrogen 020579 020084 020039 020082 5-22
260 Nitrogen 020579 020089 020039 020082 5-23
400 Nitrogen 020579 020084 020039 020082 5-23
260 Nitrogen 020579 020089 020039 020082 5-24
400 Nitrogen 020579 020084 020039 020082 5-24
260 Oxygen 120390 120384 020623 020975 5-25
340 Oxygen 120390 120384 120460 120836 5-26
260 Nitrogen 120390 120386 020039 020968 5-27
400 Nitrogen 120390 120387 020039 020968 5-27
260 Nitrogen 120390 120386 020039 020968 5-28
400 Nitrogen 120390 120387 020039 020968 5-28
*
S
T
A
N
D
A
R
D
**
B
E
V
E
L
Mild
Steel
Stainless
Aluminum
Mild
Steel
Mild /
Stainless
Aluminum
*
S
T
A
N
D
A
R
D
**
B
E
V
E
L
Mild /
Stainless
Aluminum
Mild /
Stainless
Aluminum
* Use standard consumables with the PAC620 if the torch will only be making cuts 90° to the work surface.
** Use bevel consumables with the PAC620 if the torch will be making cuts between 45° and 90° to the work surface.
WARNING
CE countries must operate the PAC620 machine torch using a special CE retaining cap in order to
comply with CE regulations. Cap removal tool (004732) must be used to put on and remove the retaining
caps. Part numbers for the CE retaining caps are indicated in the cut charts.