Canon REALiS X600 - Manual (Page 53)

User Command Specifications 9．Details of command 6AXR-Ｙ
1 6AXR-Y
6AXR-Y
6AXR=<R hue: Number>▽<R saturation: Number>
6AXG=<G hue: Number>▽<G saturation: Number>
6AXB=<B hue: Number>▽<B saturation: Number>
6AXC=<C hue: Number>▽<C saturation: Number>
6AXM=<M hue: Number>▽<M saturation: Number>
6AXY=<Y hue: Number>▽<Y saturation: Number>
Setting values for hue and color saturation (–20 to 20)
<Hue: Number>▽<Saturation: Number>
This sets the 6-axis correction of the hue and color saturation for R to Y.
-1
A "busy" response is given while the zoom or focus lens is being driven.
-2
-3
Menu
[Image adjustments] - [Advanced color adjustments] - [6-axis color adjustments]
-4
-5
Setting
> 6AXR=-8, 5
< i:OK
Reference
> GET 6AXR or ?6AXR This retrieves the R hue and color saturation.
< g:6AXR=12, -8
Obtain settable parameter range (Min, Max)
> RANGE 6AXC
< r:6AXC=N,-20,20,-20,20
* Commands are indicated by ">", and responses are indicated by "<".
Supported Command States
OFF ON PM
Ч ○ Ч
Ч ○ Ч
* If a command cannot be supported, 'INVALID_MODE' or 'NOT_POWER_SUPPLIED' is returned as an error response.
* "i:BUSY" may be returned if the power status is being switched.
The R hue is set to –8, and the color saturation is
set to 5.
01.00** 01.01** 01.01** 01.01**
SX50 SX6 SX60 X600
Commands
Function
Parameter
Description
Response
Format
Example
6-axis correction R-Y hue/saturation settings
"i:OK" is returned if the parameter was set properly.
Model
SX50
SX6
These commands take effect when 6-axis adjustment (6AX) has been selected by the
advanced color adjustment command (ACADJUST) or when they have been set to valid using
the 6-axis adjustment command (6AXADJ), and they can be set separately.
Number
For details, refer to the RANGE command.
This command is the same as the menu functions in the table below.
Mode Control Setting Reference
It can be executed when the projector is in both the remote mode and power-on status at the
same time.
The RANGE command can be used to obtain the parameter range that can be set at
that time.
This sets the currently selected input signal and image mode.
The current color adjustment values can be acquired using the applicable GET commands.
SX60
X600
Model Power Input Mode
Remote Local None
Remarks
D-RGB A-RGB1 A-RGB2 Comp Video S-Video D-Video SCART
SX50 ○ ○ ○ ○ ○ ○ – – ○ ○ ×
SX6 ○ ○ ○ ○ ○ × ○ ○ ○ ○
SX60
X600
○
Any value from -20 to 20 can be set for the hue
and saturation of the C (cyan) color.
Commands
supported
For all other responses, refer to "Error List."
(Refer to the ZCONTDRV command and FCONTDRV command.)
[Image adjustments] - [Advanced adjustments] - [6-axis color adjustments] -
[Adjustments]
For details, refer to the GET command.
○ ○ ○ ○
PAGE 45