Yaskawa VS-616G5 Series Revision F Programming Manual - Manual (Page 7)

VS-616G5 Programming Manual 7
Menu Operation
Inverter operation is enabled.
Inverter status is displayed.
A Initialize
Language selection in LCD display.
Constant access levels, control method
selection and initializing passwords.
Programming
Parameters are set/read. Items to be set/
read vary depending on the access level
setting.
Auto-tuning
Motor parameters are automatically set
by inputting turning data (motor name-
plate values) when performing vector.
Modified Constants
Only parameters that have been changed
from the factory setting are set/read.
U Monitoring Items
Monitor
B Application
Application
C Tuning
Tuning
D Reference
Reference
E Motor Parameters
Motor
F Option
Option
H Control Circuit Terminals
Terminal
L Protection
Protection
O Digital Operator
Operator
Group Function Display Access Level
U1 Status monitoring Monitor Q, B, A
U2 Fault trace Fault Trace Q
U3 Fault history Fault History Q
A1 Initialization Initialize Q
A2 User setting parameter User Parameters A
B1 Operation method selection Sequence Q, B, A
B2 DC injection braking DC Braking B
B3 Speed search Speed Search A
B4 Timer function Delay Timers A
B5 PID control PID Control A
B6 DWELL function Reference Hold A
B7 Droop control Droop control A
B8 Energy-saving control Energy Saving A
B9 Zero Servo Zero Servo A
C1 Accel/decel time Accel/Decel Q, B, A
C2 S-curve characteristics S-curve Acc/Dec A
C3 Motor slip compensation Motor-slip Comp B. A
C4 Torque compensation Torque Comp B, A
C5 ASR ASR Tuning B, A
C6 Carrier frequency Carrier Freq BA
C7 Hunting prevention Hunting Prev A
C8 Factory-tuning constant Factory Tuning A
D1 Frequency reference value Preset Reference Q, A
D2 Upper/lower limits Reference Limits B
D3 Jump frequency Jump Frequencies B
D4 Sequence Sequence A
D5 Torque reference Torque Control A
E1 V/f pattern V/F Pattern Q
E2 Motor parameters Motor Setup Q, A
E3 Motor 2 control method Motor 2 Ctl Meth A
E4 V/f pattern/2 V/f Pattern 2 A
E5 Motor 2 constants Motor 2 Setup A
F1 PG speed control card PG Option setup Q, B, A
F2 Analog reference card A1-14 Setup B
F3 Digital input card DI-08, 16 Setup B
F4 Analog monitor card AO-08, 16 Setup B
F5 Digital output card DO-02 Setup B
F6 Digital output card DO-08 Setup B
F7 Pulse monitor card PO-36F Setup B
F8 SI-F/G card SI-F/G B
F9 DDS-B/SI-B card DDSS/SI-B B
H1 Sequence input Digital Inputs B
H2 Sequence output Digital Outputs B
H3 Analog input Analog Inputs B, A
H4 Analog output Analog Outputs B
H5 MODBUS communication (RS-485) Serial Com Setup A
L1 Motor electric thermal overload relay Motor Overload B
L2 Momentary power loss ride-through PwrLoss Ridethru B, A
L3 Stall prevention Stall Prevention B, A, F
L4 Frequency Detection Ref Detection B, A
L5 Fault retry Fault Restart B
L6 Overtorque detection Torque Detection B, A
L7 Torque limit Torque Limit B
L8 Hardware protection Hdwe Protection B, A
O1 Display selection Monitor Select B, A
O2 Key selection Key Selections B, A
VS-616G5 Parameter Tree
VS-616G5 Parameter Tree