Motorola DSP56301 User Manual
Page 142
HI32 DSP-Side Programming Model
6
-24
DSP56301 User’s Manual
19
HIRD
0
UB
Host Interrupt Request Drive Control
Controls the output drive of the HIRQ pin when the HI32 is in a
Universal Bus mode (DCTR[HM]
=
$2 or $3). When HIRD is cleared,
the HIRQ pin is an open-drain output—that is, driven low when
asserted, released (high impedance) when deasserted. When HIRD is
set, the HIRQ pin is always driven. The value of HIRD can be changed
only when DSR[HACT] = 0. HIRD is ignored when the HI32 is not in a
Universal Bus mode (DCTR[HM]
≠
$2 or $3).
Note:
The HDSM, HRWP, HTAP, HDRP, HRSP, HIRH, and HIRD
bits affect the host port pins directly. To assure proper
operation, these pins can be changed only when DSR[HACT]
= 0. The HM[2–0] bits must not be changed together with
these bits (that is, in the same core write).
18
HIRH
0
UB
Host Interrupt Request Handshake Mode
Controls the handshake mode of the HIRQ pin when the HI32 is in a
Universal Bus mode (DCTR[HM]
=
$2 or $3). The HI32 asserts HIRQ
when a host interrupt request (receive and/or transmit) is generated in
the HI32. When HIRH is cleared and a host interrupt request is
generated, HIRQ is asserted for the number of DSP56300 core clock
cycles specified CLAT[LT[7–0]] and then deasserted. The duration of
the HIRQ pulse is expressed as follows:
HIRQ_PULSE_WIDTH = (LT[7–0]_Value + 1) • DSP56300_Core_clock_cycl
e
If HIRH is set, HIRQ is deasserted when the interrupt request source is
cleared (by the corresponding host data access), masked (by TREQ = 0
or RREQ = 0), or disabled by the DMA enable bit HCTR[DMAE]. The
value of HIRH can be changed only when DSR[HACT] = 0. HIRH is
ignored when the HI32 is not in a Universal Bus mode (DCTR[HM]
≠
$2 or $3).
17
HRSP
0
UB
Host Reset Polarity
Controls the polarity of the HRST pin when the HI32 is in a Universal
Bus or the GPIO mode (DCTR[HM]
=
$2, $3, or $4). If HRSP is cleared,
the HRST pin is active high and the HI32 is reset if the HRST pin is high
(that is, asserted). If HRSP is set, the HRST pin is active low and the
HI32 is reset if the HRST pin is low (that is, asserted). The value of
HRSP can change only when DSR[HACT] = 0. HRSP is ignored in PCI
mode (DCTR[HM] = $1).
16
HDRP
0
UB
Host DMA Request Polarity
Controls the polarity of HDRQ pin when the HI32 is in a Universal Bus
mode (DCTR[HM]
=
$2 or $3). If HDRP is cleared, the HDRQ pin is
active high and the HI32 requests DMA service by driving the HDRQ
pin high (that is, asserted). If HDRP is set, the HDRQ pin is active low
and the HI32 requests DMA service by driving the HDRQ pin low (that
is, asserted). The value of HDRP can change only when DSR[HACT] =
0. HDRP is ignored when the HI32 is not in a Universal Bus mode
(DCTR[HM]
≠
$2 or $3).
Table 6-10. DSP Control Register (DCTR) Bit Definitions (Continued)
Bit Number
Bit Name
Reset
Value
Mode
Description