Top, front, and rear panels g mix out jacks, H lamp connector, I monitor out jacks – Yamaha DSP5D User Manual

Page 19: J cue out jacks, K stereo out a/b jacks, L matrix out jacks, M dc power input connector, N 2tr in analog jacks 1/2, O time code input jack, P to host connector

Advertising
background image

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Operating section

19

2

T

op, front, and rear panels

G MIX OUT jacks

These are XLR-3-32 (balanced) jacks that output ana-
log signals such as those that are patched from MIX
channels 1–24. Nominal output level is +4 dBu.

H LAMP connector

This is a four-pin female XLR output jack for supply-
ing power to a gooseneck lamp. (These jacks are
provided at three locations). The location of these jacks
differs between the PM5D model and the PM5D-RH
model.

I MONITOR OUT jacks

These are XLR-3-32 (balanced) jacks that output the
monitor signal selected in the MONITOR section of
the top panel. Nominal output level is +4 dBu.

Note

Although the various output jacks and 2TR IN ANALOG jacks
have a nominal input/output level of +4 dBu (maximum level is
+24 dBu), an internal switch allows this to be changed to
–2 dBu (maximum level +18 dBu) if necessary. For details,
contact your Yamaha dealer.

J CUE OUT jacks

These are XLR-3-32 (balanced) jacks that output the
cue monitor signal from the channel selected by its
[CUE] key. Nominal output level is +4 dBu.

K STEREO OUT A/B jacks

These are XLR-3-32 (balanced) jacks that output the
analog signals of the STEREO A/B channels. Nominal
output level is +4 dBu.

L MATRIX OUT jacks

These are XLR-3-32 (balanced) jacks that output the
analog signals of MATRIX channels 1–8. Nominal out-
put level is +4 dBu.

M DC POWER INPUT connector

This is a connector for connecting the PW800W power
supply. Use the dedicated cable included with the
PM5D to make the connection.

N 2TR IN ANALOG jacks 1/2

These are XLR-3-31 (balanced) jacks that input stereo
analog signals from an external source. Nominal input
level is +4 dBu.

O TIME CODE INPUT jack

This is an XLR-3-31 (balanced) jack that receives
SMPTE time code (LTC) from an external source.

P TO HOST connector

This is a USB (type B) connector that allows communi-
cation with a computer.

Note

PM5D Editor and the USB-MIDI driver required for connection
with your computer can be downloaded from the Yamaha
website listed below.
http://www.yamahaproaudio.com/

7

8

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

C

R

L

R

L

R

L

R

L

8

7

6

5

4

3

2

1

M

J

9

K

L

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

IN

R

L

R

L

SMPTE

USB

OUT

IN

75

ON OFF

2

1

COAXIAL

COAXIAL

AES/EBU

AES/EBU

AES/EBU

AES/EBU

3

2

1

3

THRU

OUT

IN

N

X

Y

VUT

Q

R

S

Z

a

W

P

O

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Advertising