Metrohm 833 IC Liquid Handling Unit - Manual (Page 122)

10 Appendix
833 IC Liquid Handling Unit / Gebrauchsanweisung 8.833.1001
114
Pump type.............................................91
Pumpable liquids ..................................91
PVDF compression fitting 64
Assembly ....................................60, 61
Figure ..........................................59, 71
Ordering designation................99, 102
Q
QA .......................................................107
Quality assurance ...............................107
Quality Management ..........................110
R
Rear panel............................................... 7
Recovery rate........................................64
Recycling ........................................35, 49
Regeneration.........................................82
Regeneration solution...29, 33, 40, 46, 82
Remedying faults ..................................76
Remote
Cable.....................................15, 16, 18
Connection............................14, 16, 18
via 761 Compact IC....................14
Control
via 819 IC Detector.....................16
via 830 IC Interface.....................18
line...............................................15, 17
Remote interface
Actuator 13
Technical data............................92
Actuator 14
Figure............................................ 7
Technical data............................92
Pump 15
Figure............................................ 7
Technical data............................92
Remote interface socket occupancy....92
Replace
Actuator rotor ....................................85
Cation exchanger..............................85
Suppressor .......................................85
Replacing the dialysis membrane........89
Replacing the pump tubing..................80
Rinse .........................................67, 73, 80
Rinse dialysis system ...........................67
Rinsing ..................................................51
Rinsing solution ..................29, 34, 40, 46
Rinsing time ..........................................63
Roller head
Ordering designation......................104
S
Safety information...........................10, 92
Safety rules ...........................................10
Safety specification...............................92
Sample ............................................51, 70
Sample determination ..........................66
Sample feed to filtration cell .................71
Sample preparation connection 34
Connect capillary .............39, 40, 45,46
Figure ................................................36
Sample preparation module.................36
Assembly ..........................................84
Cleaning............................................83
Information ........................................49
Regeneration ....................................82
Ordering designation........................97
Sample preparation module 33
Description.......................................... 3
Figure................................................ 36
Ordering designation........................ 97
Sample preparation module
connections .......................................... 39
Screw 47
Dismantle dialysis cell ...................... 89
Figure................................................ 50
Ordering designation........................ 99
Screw 70
Assembly .......................................... 69
Figure................................................ 68
Ordering designation...................... 101
Sealing ring 44
Figure................................................ 50
Ordering designation........................ 99
Sealing ring 68
Assembly .......................................... 69
Figure................................................ 68
Ordering designation...................... 101
Separating column
Fixing........................................... 28, 33
Rinsing ........................................ 28, 32
Separating column 53
Mounting..................................... 28, 32
Serial number 10
Figure.................................................. 7
Setting screw 12
Figure.................................................. 7
Step Adjustment ............................... 87
Setting the mains voltage............... 12, 13
Sleeve nut 85
Assembly .................................... 84, 86
Figure................................................ 84
Slot 48
Figure................................................ 50
Solvent handling ................................... 10
SOP..................................................... 107
Spring lever 7
Assembly pump tubing .................... 20
Figure............................................ 6, 19
Tubing cassette assembly ............... 80
Standard equipment............................. 95
Standard operating procedures......... 107
Start mode ............................................. 25
Start pump with startup hardware .......... 25
Start-up
833 LH Sample Preparation Unit ..... 41
833 LH Suppressor Unit................... 34
833 Pump Unit.................................. 30
833 Sample Preparation Module .... 41,
47
LH Sample Preparation Unit............. 47
Suppressor module.......................... 34
Start-up the 833 IC Liquid Handling
Dialysis Unit .......................................... 62
Step ....................................................... 26
Step adjustment 12
Adjust rotor ................................. 87, 88
Figure.................................................. 7
Stopped flow technique ......................... 4
Stopper
Color code .......................... 21, 97, 104
Stopper 20
Assembly .......................................... 20
Figure................................................ 19
Pump tubing assembly .................... 80
Storage ................................................. 93
Sulfuric acid .............................. 33, 35, 49
Suppressor
37, Figure ......................................... 39
Assembly.......................................... 84
Replace ............................................ 85
Suppressor ............................................ 24
Suppressor connection 25
Connect capillary ....................... 33, 34
Figure................................................ 31
Suppressor holder 88
Assembly.................................... 84, 86
Suppressor inlet capillary 27
Figure................................................ 32
Suppressor inlet capillary 28
Figure................................................ 32
Suppressor inlet capillary 31
Figure................................................ 32
Suppressor inlet capillary 64
Figure................................................ 27
Mounting........................................... 28
Suppressor inlet capillary 65
Figure................................................ 27
Mounting........................................... 29
Suppressor inlet capillary 68
Figure................................................ 27
Mounting........................................... 29
Suppressor module
Cleaning ........................................... 83
Information ....................................... 35
Regeneration .................................... 82
Suppressor module 24
Connection ....................................... 32
Description ......................................... 2
Figure................................................ 31
Ordering designation ....................... 96
Suppressor module 33
Connection ................................. 39, 45
Suppressor module 70
Connection 1 .................................... 29
Mounting........................................... 28
Suppressor outlet capillary 29
Figure................................................ 32
Suppressor outlet capillary 30
Figure................................................ 32
Suppressor outlet capillary 32
Figure................................................ 32
Suppressor outlet capillary 66
Figure............................................... 27
Mounting........................................... 29
Suppressor outlet capillary 67
Figure................................................ 27
Mounting........................................... 29
Suppressor outlet capillary 69
Figure................................................ 27
Mounting........................................... 29
Suppressor unit ................................ 2, 35
Switching instrument on/off ........... 13, 23
T
Technical data ...................................... 91
Time program....................................... 54
Total ionic concentration...................... 64
Transfer time................................... 63, 78
Transfer to sample loop ....................... 51
Transport damage........................ 11, 108
Troubleshooting ................................... 76
Tubing cassette 4
Assembly.......................................... 80
Assembly pump tubing.................... 20
Figure............................................ 6, 19
Ordering designation ..................... 104
Tubing connection system............. 58, 71
Tweezers 6.2831.010 ..... 56, 69, 100, 102