Verilink 8100A (34-00237) Product Manual User Manual
Verilink
Advertising
This manual is related to the following products:
8108 Series IAD (34-00339.B) Product Manual, 8508 Series IAD (34-00339.B) Product Manual, 8208 Series IAD (34-00339.B) Product Manual, 8308 Series IAD (34-00339.B) Product Manual, 7500p Series IAD (34-00334.B) Product Manual, 7200p Series IAD (34-00334.B) Product Manual, 7000 Series (34-00334) Product Manual
Table of contents
Document Outline
- Front Matter
- 8104, 8108, 8104s, 8108s, 8504, 8508, 8504s, 8508s
- 8208, 8208s, 8304, 8308, 8304s, 8308s
- 8216s, 8224s, 8316s, 8324s, 8512s, 8516s, 8524s
- Copyright Notice
- Trademarks
- Documentation Disclaimer
- Warranty
- FCCRequirements
- Canadian Emissions Requirements
- Safety Precautions
- Table of Contents
- Preface
- Chapter 1 Introduction
- Chapter 2 Quick Start Guide
- Unpacking the IAD
- Installing the IAD
- AC Power and Uninterruptible Power Supply
- Clearance Requirements
- Wiring Requirements
- Connecting the IAD Via a Terminal Emulator
- Setting the Ethernet Port IP Address
- Setting the WAN Port IP Address
- Resetting the IAD
- Connecting via Telnet
- Basic IAD Configuration
- Connecting LAN, WAN, and Telephones
- Confirming Proper Setup
- Chapter 3 Administration
- IAD Security
- Setting Up SNMP
- SNMP Configuration Menu
- Enable/Disable SNMP via IP
- Enable/Disable SNMP via EOC
- Enable SNMP via Both IP and EOC
- Disable SNMP via Both IP and EOC
- Configure System Contact
- Configure System Name
- Configure System Location
- Configure SNMP Community
- Configure SNMP Trap Host IP Address
- Enable/Disable SNMP Traps via EOC
- Configure Restart Trap Maximum Delay
- Defining Different SNMP Version 3 Categories
- SNMP Configuration Menu
- LAN Configuration Menu
- Upgrading the System
- Utilities Menu
- Chapter 4 Configuration
- Introduction
- Managing Configuration Files
- WAN Configuration
- Basic WAN Setup Tasks
- Setting the WAN Port IP Address
- Identifying the WAN Interface and Datalink Protocol
- WAN Configuration Menu
- Configure Physical Interface - SDSL
- Quick Configuration for SDSL WAN
- Configure Physical Interface - T1/E1
- Configure Physical Interface - ADSL
- Configure Physical Interface - SHDSL
- Configure Physical Interface - USI
- Configure Datalink Protocol
- Configure ATM PVCs
- Configure ATM Options
- Configure DLCIs
- Configure Frame Relay Options
- Router Configuration
- Basic Router Setup Tasks
- Router Configuration Menu
- Configure Port IP Address
- Unconfigure Port IP Address
- Configure Port Maximum Transmission Unit (MTU)
- Configure Port TCP MSS Adjustment
- Add/Remove a Static or Source Route
- Enable/Disable RIP
- Configure RIP Version by Port
- Configure RIP Poisoned Reverse by Port
- Configure DNS Client
- Configure DHCP Client
- Configure DHCP Relay
- Configure Telnet Server Port
- Configure IP QoS
- Configure IP Filtering
- Configure IP Header Compression (IPHC)
- Configure LAN IP Broadcast Destination
- Configure Domain Name
- Configure Host Name
- Remove Host and Domain Names
- Display Route Table
- Bridge Configuration
- Basic Bridge Setup Tasks
- Bridge Configuration Menu
- Enabling and Disabling Bridging
- IP Over Bridging
- Enable/Disable Bridging Globally
- Enable/Disable Bridging by Port
- Bridge Aging Timer
- Enabling and Disabling Spanning Tree
- Enable/Disable Spanning Tree Globally
- Enable/Disable Spanning Tree by Port
- Configure Spanning Tree Bridge Priority
- Configure Spanning Tree Port Priority
- Configure Spanning Tree Hello Time
- Configure Spanning Tree Maximum Age
- Configure Spanning Tree Forward Delay
- Configure Spanning Tree Path Cost
- Delete Bridge Forwarding Database Entry
- Voice Path Configuration
- Interworking Connections
- Firewall Configuration
- DHCP Server Configuration
- Basic DHCP Server Setup Tasks
- DHCP Server Configuration Menu
- Enable/Disable DHCP Server
- Enable/Disable Checking Additional DHCP Servers
- Enable/Disable DHCP Debug Messages
- Configure DHCP Server Parameters
- Configure DHCP Address Range Pool
- Configure DHCP Client Entry
- Display DHCP Configuration
- Display DHCP Server Statistics
- Display DHCP Server Assigned and Unassigned Addresses
- Display DHCP Entry Details
- Delete a DHCP Client Entry
- Delete a DHCP Assignment Entry
- Multicast Configuration
- NAT Configuration
- NAT Configuration Menu
- Enable/Disable NAT Debug Messages
- Enable/Disable NAT Translation by Port
- Configure NAT TCP and UDP Timeouts
- Configure NAT Port Range
- Configure NAT Local Server Entry
- Configure NAT Alias Entry
- Display NAT Statistics
- Display NAT Connection Table
- Display NAT Connection Details
- Display NAT Local Server Table
- Display NAT Alias Table
- Clear NAT Statistics
- Delete IP Address from NAT Tables
- Delete NAT Local Server Entry
- Delete NAT Alias Entry
- NAT Configuration Menu
- Setting PPP Options
- Setting Derived Timing Options
- Chapter 5 Reports
- Reports Menu
- Current Configuration Report
- Network Statistics Reports
- Interface Statistics Reports
- Media Statistics Reports
- Route Table Report
- ARP Table Report
- Bridge Forwarding Database Report
- Bridge Status Report
- PPP Authorization Entries Report
- System Uptime Report
- Memory Statistics Reports
- Tasks Run Time
- Zero All Statistics
- Reports Menu
- Chapter 6 Command Line Interface
- Chapter 7 Troubleshooting and Diagnostics
- Chapter 8 Verification
- Appendix A Menu Map
- Appendix B Specifications
- T1/E1 (8208/8208s)
- T1/E1 (8216s and 8224s)
- SDSL (8304/8304s and 8308/8308s)
- SDSL (8316s and 8324s)
- ADSL (8104/8104s and 8108/8108s)
- SHDSL (8504/8504s and 8508/8508s)
- SHDSL (8512s, 8516s, and 8524s)
- Appendix C High-Port Count (HPC) Battery Backup Unit (BBU)
- Appendix D Applications Notes
- Appendix E Glossary
- Hardware Limited Warrranty