Document Outline

• Installation Guide for Galaxy Power Systems
• Table of Contents
• List of Figures
• List of Tables
• Introduction
  • Product Documentation
    • This Installation Guide
    • Revisions
    • Related Documentation
  • Customer Service Contacts
    • Customer Service, Technical Support, Product Repair and Return, and Warranty Service
    • Customer Training
    • Downloads and Software
• Safety
  • Safety Statements
  • Warning and Safety Symbols
  • Precautions
  • Special Installation Notes
    • Deutsch - German
    • Español - Spanish
• Getting Started
  • Tools and Hardware
  • Torque Settings for Hardware
  • Unpacking
  • Location
• System Electrical Architecture Overview
  • Introduction
    • Bonding Network
    • Facility
  • Single Cabinet System
  • Distributed Architecture
  • Centralized Architecture
• Cabinet Floor Mounting and Battery Stand Connection
  • Cabinet Installation
    • Mounting Plates for Unigy Batteries
    • Mounting Specifications
    • Procedure
  • Cabinet Ground and Central Office Ground
    • Cabinet Ground Procedure
    • Central Office Ground Procedure
  • Recommended Cable Rack Layout
• Centralized or Distributed Architecture Connections
  • Multiple-Cabinet Installations
    • Special Requirements
  • Centralized Architecture
    • DC Power Connections to Central Bus Bar
    • Remote Voltage Sense and System Shunt for Galaxy Millennium Controller
    • Remote Voltage Sense and System Shunt for Galaxy Vector Controller
  • Distributed Architecture
    • Intercabinet DC Power Bus Connections
  • Intercabinet Alarm and Serial Bus Connections
    • BLJ2/3 to BLJ2/3 (Millennium Controller)
    • BLJ3 to BLJ3 (Vector Controller)
• AC Connection and Wiring
  • Wire Sizing and Ampacity
  • AC Input Schemes
    • 595 Rectifiers (48V, 200A) and 595LT Rectifiers (48V, 220A)
    • 596 Rectifiers (24V, 100A/125A and 48V, 50A/100A)
  • AC Cable Routing
  • Rectifier Positions
  • AC Input Panels Cross Reference
  • AC Input Panels
  • Field Modification of the 1-Phase Circuit Breaker AC Panel for use with Phase-Neutral Input Circuits - ED83142-30 G-6, G7, G19, G21, or G23
    • Bottom Cable Feed Options for GPS 4848/100
  • Completing the AC Connection
• DC Distribution Assembly and Connections
  • Overview
  • DC Distribution Panels Cross Reference
  • Connecting Loads
    • Cable Routing Strategy
    • Capacitor Charge Unit
    • Mounting Large Circuit Breakers
    • Mounting Small Plug-in Circuit Breakers and Fuses
  • Disrtibution Panels
  • Low Voltage Disconnect Feature
    • EBV Circuit Pack
• Converters
  • Introduction
  • Installing the Converter Carrier
  • Setting the CIC ID
  • Converter Wiring
• Remote Peripheral Monitoring
  • Overview
    • RPM Modules
    • Current Limiting Resistors
    • Mounting Locations
  • RPM Installation
• Battery Connection Panels
  • Connecting and Disconnecting Batteries
  • Battery Connection Panels Cross Reference
    • Additional Battery Leads
  • Battery Connection Panel Options
  • Connecting (+) and (-) Conductors
    • +24-volt Systems
    • -48-volt Systems
  • Installing Battery Connection Panels
  • Contactor Control Board
    • Full-Height Cabinet
    • Half-Height Cabinet
  • Battery and Alarm Fuses and Circuit Breakers
• Thermal Probe and 210E Connections
  • Introduction
  • Cable Letter Codes
  • Connecting Thermal Probe Cable Assembly
    • Millennium Controller
    • Vector Controller
  • Wiring Schematic for Extender Cable
  • Cable Routing
  • Connecting Thermal Probe Assembly
    • BLJ Board
    • Millennium Controller
  • Connecting a 210E Module to the Controller or BLJ Board
  • Connecting Cable Assembly to the 210E
  • Connecting Cable Assembly to Thermal Probes
  • Monitoring a 210E Alarm Signal, BLJ-BIC7/8 with Millennium
• Fascia Cover Installation
  • Introduction
  • Installing the Fascia Covers
• Connection of Office Alarms
  • Introduction
  • Connecting Controller Alarms
• Power Up and Installation Completion
  • Initial System Checkout and Preparation for Power Up
  • Controller Front Panels
    • Millennium
    • Vector
  • Initial Power Up of the System
    • Rectifier Installation Notes
    • Install First Rectifier
    • Install Converter Cards
    • Verify Controller
    • Set Rectifier ID
  • Installing Rectifiers and Converters
  • Lamp Test
  • Voltage Calibration
  • Setting the System Float Voltage
  • Setting the System Shunt
  • Setting the Low-Voltage Battery Disconnect Feature
  • Setting the Low-Voltage Load Disconnect Feature
  • Connecting Batteries
  • Testing Rectifiers and Load Share
  • Testing Temperature Compensation (Optional Feature)
  • Testing Additional Alarms
  • Testing the BD Alarm and High Voltage Shutdown
  • Galaxy Millennium Controller System Alarm Test
  • Connecting to Load
• Addition or Modification to a Galaxy Power System
  • Upgrading a GPS4848 System to a GPS4848/100 System
  • Adding an ED83143-31 Distribution Panel to a GPS
  • Installing an LVLD Contactor (if required)
  • Adding a Cabinet to an Existing GPS System with Distributed Architecture.
  • Replacing the Bay Interface Card (BIC) or BLJ3 Terminal Board