Document Outline

• Preface
  • Regulatory and Safety Statements
  • Environmental Considerations for Installation of McDATA Equipment
  • General Precautions
  • ESD Precautions
• Introduction
  • Introducing the UltraNet Edge 3000
  • UltraNet Edge 3000 Benefits
  • UltraNet Edge 3000 Features
  • UltraNet Edge 3000 Security
• Hardware Configurations
  • UltraNet Edge 3000 Featurization
  • Typical Configuration of the UltraNet Edge 3000
    • Ethernet Configurations
    • ATM WAN Configurations
    • FC/SCSI Tape Pipelining
  • Valid Hardware Interface Configurations
  • Fibre Channel Card Dependencies
    • FC/SCSI E_port Configurations
    • FC/SCSI F_port Configurations
    • FC/SCSI N_port Configurations
    • FICON Port Configurations
  • Internal Fibre Channel Switch (FCSW)
  • Hardware Components
  • Indicators, Switches, and Interfaces
• Network Design Criteria
  • Network Design
    • Ethernet Network Criteria
    • ATM Network Criteria
  • Network Routing Options
    • Dedicated
    • Load Balancing
    • Fail Over
  • Switch WWN Proxy
  • E_Port Disk Streaming Network Recommendations
  • Required Minimum Hardware for E_Port Disk Streaming
  • E_Port Disk Streaming Compatibility Matrix
  • Fibre Channel Frame Level CRC
    • Frame Level CRC on the FCBB Card
    • Frame Level CRC on the FCXL2 Card
  • Fibre Channel End to End CRC
  • Minimum Requirements for CRC
  • Fibre Channel MTU Batching
• Building a Custom Edge 3000 Chassis
  • Building the Custom Chassis
    • Starting UltraNet ConfigManager
    • Using the Custom Chassis Wizard
• Configuring an E_Port Extension over an Ethernet WAN
  • Configuring a 1x1 Ethernet Wide Area Network
    • Gathering the IP Addresses
    • Starting UltraNet ConfigManager
    • Adding Nodes for an Ethernet WAN Configuration
    • Adding a Fibre Channel Interface
    • Setting the Initial Configuration
    • Setting the License Information
    • Adding an IP Circuit
    • Creating a Data Path
  • Delivering the Configured Network
    • Setting the Delivery Properties
    • Delivery Wizard
    • Deliver Network
    • Viewing Logs
• Configuring an F_Port Extension over an Ethernet WAN
  • Configuring a 2x2 Ethernet Wide Area Network
    • Gathering the IP Addresses
    • Starting UltraNet ConfigManager
    • Adding Nodes for an Ethernet WAN Configuration
    • Setting the Initial Configuration
    • Setting the License Information
    • Adding an IP Circuit
    • Creating Data Paths for Fibre Channel Switch Interfaces
  • Delivering the Configured Network
    • Setting the Delivery Properties
    • Delivery Wizard
    • Deliver Network
    • Viewing Logs
• Configuring an E_Port Extension over an ATM WAN
  • Configuring a 1x1 ATM Wide Area Network
    • Gathering the IP Addresses
    • Starting UltraNet ConfigManager
    • Adding Nodes for an ATM WAN Configuration
    • Setting the Initial Configuration
    • Setting the License Information
    • Adding an ATM Circuit
    • Creating a Data Path
  • Delivering the Configured Network
    • Setting the Delivery Properties
    • Delivery Wizard
    • Deliver Network
    • Viewing Logs
• Configuring FICON Extension
  • Configuring a 1x1 Ethernet Wide Area Network
    • Gathering the IP Addresses
    • Starting UltraNet ConfigManager
    • Adding Nodes for an Ethernet WAN Configuration
    • Adding a Fibre Channel Interface
    • Setting the Initial Configuration
    • Setting the License Information
    • Adding an IP Circuit
    • Creating a FICON Data Path
    • Using the FICON Global Settings Wizard
  • Delivering the Configured Network
    • Setting the Delivery Properties
    • Delivery Wizard
    • Deliver Network
    • Viewing Logs
• Configuring Tape Device Extension
  • Setup Prior to Edge Configuration
  • Network Configuration Examples
    • Example of Uni-directional Configuration - No Zoning
    • Example of Bi-directional Configuration with Zoning
    • Example of Bi-directional Configuration - Zoning and Optional LUN Mapping
    • Required Fibre Channel Switch Zoning
    • Required Static Edge LUN Mapping
    • Required Source WWN Filtering
  • Configuring Tape Device Extension
    • Gathering the IP Addresses
    • Starting UltraNet ConfigManager
    • Adding Nodes for an Ethernet WAN Configuration
    • Setting the Initial Configuration
    • Setting the License Information
    • Adding an IP Circuit
    • Creating a Data Path for Fibre Channel Device Extension Interfaces
    • Static Mapping the LUNs and Filtering the Source WWN
  • Delivering the Configured Network
    • Setting the Delivery Properties
    • Delivery Wizard
    • Deliver Network
    • Viewing Logs
• FC/SCSI Tape Pipelining
  • Buffering, Emulation, and Data Protection
    • Buffering and Emulation
    • Device Error Recovery
    • UltraNet Edge 3000 Emulation
    • Protecting the Data
  • UltraNet Edge 3000 Specific
    • Fibre Channel
    • Tape Only
    • LUN Mapping
  • Dynamic Target LUN Discovery and LUN Mapping
    • Overview
    • Target Discovery
    • LUN Discovery
    • LUN Refresh
    • Dynamic LUN Mapping
    • Static LUN Mapping
    • Managing the WWN to Edge Target LUNs
• Product Support and Software Maintenance
  • SNMP Support
  • Upgrading the UltraNet Edge 3000 Software
    • Verify your Current Software Version
    • Upgrading the UltraNet Edge 3000 - On-Site Local
    • Upgrading the UltraNet Edge 3000 - Remote Dial-up
    • Upgrading Edge Software from 3.1.1.1 or Higher
  • UltraNet WebView Monitoring Application
    • Obtaining the UltraNet WebView Product
    • Using the WebView Application
    • Browser and System Requirements for WebView
    • WebView Security
    • UltraNet WebView Upgrade
  • UltraNet ConfigManager Upgrade
    • Verify the Current Version of UltraNet ConfigManager
    • Upgrading the UltraNet ConfigManager Software
• Hardware Maintenance
  • Front and Rear View of UltraNet Edge 3000 Chassis
  • Replacing the UltraNet Edge 3000 Chassis
  • Fan Assembly Removal Procedure
  • Fan Assembly Installation Procedure
  • Power Supply Removal Procedure
  • Power Supply Installation Procedure
  • Top Cover Removal Procedure
  • Top Cover Installation Procedure
  • Fibre Channel Interface Card Removal Procedure
  • Fibre Channel Interface Card Installation Procedure
  • 10/100 Ethernet Interface Card Removal Procedure
  • 10/100 Ethernet Interface Card Installation Procedure
  • Gigabit Ethernet Interface Card Removal Procedure
  • Gigabit Ethernet Interface Card Installation Procedure
  • OC-3 ATM Interface Card Removal Procedure
  • OC-3 ATM Interface Card Installation Procedure
  • Replacing the Gigabit Ethernet Short Wave Transceiver
    • Removing the Gig-E Short Wave SFP Transceiver
    • Installing the Gig-E Short Wave SFP Transceiver
  • Replacing the Gigabit Ethernet Long Wave Transceiver
    • Removing the Gig-E Long Wave SFP Transceiver
    • Installing the Gig-E Long Wave SFP Transceiver
  • Replacing the Gigabit Ethernet Copper Transceiver
    • Removing the Gig-E Copper Transceiver
    • Installing the Gig-E Copper Transceiver
  • Replacing the OC-3 ATM Short Wave Transceiver
    • Removing the OC-3 ATM Short Wave SFP Transceiver
    • Installing the OC-3 ATM Short Wave SFP Transceiver
  • Replacing the OC-3 ATM Long Wave Transceiver
    • Removing the OC-3 ATM Long Wave SFP Transceiver
    • Installing the OC-3 ATM Long Wave SFP Transceiver
  • Replacing the Fibre Channel Short Wave Transceiver
    • Removing the Fibre Channel Short Wave SFP Transceiver
    • Installing the Fibre Channel Short Wave SFP Transceiver
  • Replacing the Fibre Channel Long Wave Transceiver
    • Removing the Fibre Channel Long Wave SFP Transceiver
    • Installing the Fibre Channel Long Wave SFP Transceiver
• Troubleshooting and Diagnostics
  • Basic Troubleshooting for the UltraNet Edge 3000
  • User Interface Commands for the UltraNet Edge 3000
    • Display the User Interface Commands
    • IP
    • TANKIO
    • ARP
    • AMDENET 10/100 WAN or Maintenance Interface
    • GNIC3 Gigabit Ethernet WAN
    • gnic3 stats
    • FCCNT
    • FCSW
    • FCXL2
    • CHARM
    • SUPPORT
    • LED Diagnostic Codes
  • Troubleshooting FC/SCSI Tape Pipelining (Device Extension)
    • Basic Troubleshooting Steps for FC/SCSI Tape Pipelining
  • Diagnostics
    • Serial Interface Connection
    • Ethernet Maintenance Interface Connection
    • Loading and Starting the Diagnostic Program
    • Exit and Reboot
  • UltraNet Edge 3000 Diagnostic Programs
    • CHARM Diagnostic Program (ACHT)
    • PowerPC Diagnostic Program (SBTT)
    • Fibre Channel Diagnostic Program (FCBB)
    • Ethernet Diagnostic Program (E10T)
    • Gigabit Ethernet Diagnostic Program (GBIT)
    • ZPCM Compression Diagnostic Program (ZPCT)
    • Flash Drive Diagnostic Program (ISBT)
  • Graceful Shutdown
• Site Preparation
  • Site Requirements
    • UltraNet Edge 3000 Chassis Dimensions
  • Clearance Requirements
    • Environmental Specifications
    • Power Requirements
• Installation and Cabling
  • Overview
  • Unpacking and Inspecting the Hardware
  • UltraNet Edge 3000 Placement
    • Table-Top
    • Rack Mount
  • Connecting the UltraNet Edge 3000
    • Setup Connection
    • Power Connection
  • Network Interface Connections
    • Fibre Channel Cabling
    • Ethernet 10/100 Cabling
    • Gigabit Ethernet Cabling
    • OC-3 ATM Cabling and Transceivers
  • Initial Power-On Procedure
  • Maintenance and Diagnostics Connections
    • Serial Interface Cabling Instructions
  • Cables and Equipment
    • McDATA-Supplied Cables and Equipment
    • Customer-Supplied Cables and Equipment
  • Preventing Damage from Electrostatic Discharge (ESD)
• Cables, Connectors, and Adapters
  • RS-232 Cables with RJ-45 Connector
  • DB Adapters
  • Fibre Channel Specifications
  • Ethernet 10/100 Specifications
  • Gigabit Ethernet Specifications
  • OC-3 ATM Specifications
• Advanced UCM Configurations
  • Configuring the Internal McDATA Fibre Channel Switch Interface
    • FCSW Tab (2 port only)
    • FC Switch Tab
  • Time Synchronization Protocol
    • Configure the Time Synchronization Protocol
  • Transport CRC Checking
  • E_Port Disk Streaming Settings
    • Enable/Disable E_Port Disk Streaming
  • F_Port Disk Streaming Settings
    • Enable/Disable F_Port Disk Streaming
• Modifying Static Routes
  • Display Static Routes
  • Verify Static Routes
  • Modify Static Routes
  • Add Static Routes
  • Delete Static Routes
• Configure SNMP
  • Adding an SNMP Trap Destination
  • Deleting an SNMP Destination
  • Sending Test Trap
  • SNMP Software Packages
• Resetting the System to Factory Defaults
  • Overview of the Sysclean Command
  • Using the Sysclean Command
• Manual Configuration of the Initial IP Settings
  • Manually Configure the Maintenance IP Port using the Command Line Interface
  • Update UltraNet ConfigManager with the Manual Configurations
• Using the Spantree Portfast Command for Cisco Routers
  • Issuing the Spantree Portfast Command
• Configuration Worksheets
  • Configuration Worksheets
    • IP Configuration Worksheet
    • ATM WAN Configuration Worrksheet
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W
  • Z