Yokogawa Standalone MW100 - Manual (Page 253)

5-40 IM MW100-01E
Pt100 *1
JPt100 *1
Pt100 (high res.)
JPt100 (high res.)
Ni100 SAMA *2
Ni100 DIN *2
Ni120 *3
Pt50
Cu10 GE *4
Cu10 L&N *4
Cu10 WEED *4
Cu10 BAILEY *4
J263B
Cu10 at 20°C
alpha=0.00392
Cu10 at 20°C
alpha=0.00393
Cu25 at 0°C
alpha=0.00425
Cu53 at 0°C
alpha= 0.00426035
Cu100 at 0°C
alpha=0.00425
Pt25 (JPt100/4)
Cu10 GE
(high resolution)
Cu10 L&N
(high resolution)
Cu10 WEED
(high resolution)
Cu10 BAILEY
(high resolution)
PT100GOST
Cu100GOST
Cu50GOST
Cu10GOST
Level
Contact input
–200.0 to 600.0°C
–200.0 to 550.0°C
–140.00 to 150.00°C
–140.00 to 150.00°C
–200.0 to 250.0°C
–60.0 to 180.0°C
–70.0 to 200.0°C
–200.0 to 550.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
0.0 to 300.0K
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–50.0 to 150.0°C
–50.0 to 150.0°C
–200.0 to 550.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 300.0°C
–200.0 to 600.0°C
–200.0 to 200.0°C
–200.0 to 200.0°C
–200.0 to 200.0°C
Vth = 2.4 V
±(0.05% of rdg + 0.3°C)
±(0.05% of rdg + 0.3°C)
±(0.05% of rdg + 0.3°C)
±(0.1% of rdg + 2°C)
±(0.05% of rdg + 0.3K)
±(0.1% of rdg + 2°C)
±(0.1% of rdg + 0.5°C)
±(0.05% of rdg + 0.3°C)
±(0.1% of rdg + 0.5°C)
±(0.1% of rdg + 2°C)
±(0.05% of rdg + 0.3°C)
±(0.05% of rdg + 0.3°C)
±(0.05% of rdg + 0.3°C)
±(0.1% of rdg + 2°C)
Threshold level accuracy: ±0.1 V
ON for 100 Ω or less, OFF for 10 kΩ or more *5
±(0.1% of rdg + 1.5°C)
±(0.1% of rdg + 1.5°C)
±(0.1% of rdg + 1.5°C)
±(0.2% of rdg + 5°C)
±(0.1% of rdg + 1.5K)
±(0.2% of rdg + 5°C)
±(0.2% of rdg + 2°C)
±(0.1% of rdg + 1.5°C)
±(0.2% of rdg + 2°C)
±(0.2% of rdg + 5°C)
±(0.1% of rdg + 1.5°C)
±(0.1% of rdg + 1.5°C)
±(0.1% of rdg + 1.5°C)
±(0.2% of rdg + 5°C)
Input
Measurement Accuracy
Integration Time: 16.67 ms
or More
Rated
Measurement
Range
Measurement Accuracy
Integration Time: 1.67 ms
Measurement
Range
Type
*1 Pt50: JIS C 1604-1989, JIS C 1606-1989/Pt100: JIS C 1604-1997, IEC 751, DIN IEC 751/JPt100: JIS C 1604-1989, JIS C 1606-1989
*2 SAMA/DIN
*3 McGRAW EDISON COMPANY
*4 Guaranteed accuracy range Cu10 GE: –84.4 to 170.0°C/Cu10 L&N: –75.0 to 150.0°C/Cu10 WEED: –20.0 to 250.0°C/
Cu10 BAILEY: –20.0 to 250.0°C
*5 Measured using a measurement current of approximately 10 μA at 200 mV range. Threshold level is approximately 0.1 V.
Highest
Resolution
(1 digit)
0.1°C
0.01°C
0.1°C
0.1°C
0.1K
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
RTD
(Measurement
current: 1 mA)
DI
Measurement interval, integration time, and filter:
Measurement
Interval
100 ms
16.67 ms
20 ms
Auto * 3
Integration
Time
Filter Rejected Noise and Notes
500 ms
Rectangular
1 s
2 s
5 s
10, 20, 30, 60 s
36.67 ms
100 ms * 4
200 ms * 5
200 ms
Trapezoidal
Rectangular
Cos
600 Hz and its integer multiples * 2
60 Hz and its integer multiples
50 Hz and its integer multiples
Automatically detects the power supply frequency and set
16.67 or 20 ms
50 Hz or 60 Hz and their integer multiples
10 Hz and its integer multiples
Fc = 5-Hz low-pass filter
Burnout
Detection
Cycle
200 ms
1 s * 1
1.67 ms
Measurement
interval
*1 When the measurement interval is 100 ms, burnout is detected in one channel per measurement interval.
Therefore, if measurement is started in a burnout condition or after a burnout occurs, burnout cannot be
detected for up to 10 measurements (approximately 1 second).
*2 Because the power supply frequency noise is not rejected, measured values may fluctuate particularly for
temperature measurements using thermocouples. If this happens, make the measurement interval longer, or
use the 4-CH High-Speed Universal Input Module.
*3 For DC power, set to 20 ms.
*4 When synchronizing time by SNTP, the integral time is set to 36.67 ms. Also in this case, noise of 50 Hz, 60
Hz, and their integer multiples is rejected.
*5 When synchronizing time by SNTP, the integral time is set to 100 ms. Also in this case, noise of 10 Hz and its
integer multiples is rejected.
Reference junction compensation:
Switch external/internal by channel, includes remote RJC function
5.5 10-CH, Medium-Speed Universal Input Module (MX110-UNV-M10) Specifications