Yokogawa Standalone MW100 User Manual
Yokogawa Sensors
Advertising
Table of contents
Document Outline
- Safety Precautions
- Conventions Used in This Manual
- Contents
- Chapter 1 Explanation of Functions
- 1.1 System Overview
- 1.2 MW100 Operation Guide
- 1.3 Functions of the Main Module
- Names and Functions of Parts
- Switches and Keys
- Connectors
- Displays
- Operation Modes and Statuses
- Measurement
- Multi interval
- Filters
- MATH
- MATH (/M1 Option)
- Report Function (/M3 Option)
- Remote RJC (RRJC)
- Burnout
- Range Over
- Alarms
- Tag Strings
- Messages
- Free Message
- Event Action Function
- Daylight Saving Time
- Timer
- Match Time
- Measurement, Computation, and Thinning Recording Operations
- Manual Sample Function
- Saving Data to the CF Card
- Communication Specifications
- E-Mail Function
- Log Information
- 1.4 Functions of the 4-CH, High-Speed Universal Input Module
- 1.5 Functions of the 10-CH, Medium-Speed Universal Input Module
- 1.6 Functions of the 30-CH, Medium-Speed DCV/TC/DI Input Module
- 1.7 Functions of the 6-CH, Medium-Speed Four-Wire RTD Resistance Input Module
- 1.8 Functions of the 4-CH, Medium-Speed Strain Input Module
- 1.9 Functions of the 10-CH, Pulse Input Module
- 1.10 Functions of the 10-CH, High-Speed Digital Input Module
- 1.11 Functions of the 8-CH, Medium-Speed Analog Output Module
- 1.12 Functions of the 8-CH, Medium-Speed PWM Output Module
- 1.13 Operation of the 8-CH Medium-Speed Analog Output Module and the 8-CH Medium Speed PWM Output Module
- 1.14 Functions of the 10-CH, Medium-Speed Digital Output Module
- 1.15 MATH Function (/M1 Option)
- 1.16 Report Function (/M3 Option)
- Chapter 2 Installation and Wiring
- 2.1 Handling Precautions
- 2.2 Installation
- 2.3 Attaching the Modules
- 2.4 Connecting Signal Wires
- Terminal Arrangement Markings on the Terminal Cover
- Attaching and Removing the Terminal Block
- Attaching the Plate with Screw Terminal and Plate with Clamp Terminals for Current
- Screw Terminal Block
- General Precautions When Wiring the Input/Output Signal Wires
- Wiring Procedures
- Wiring the Universal Input Module and DCV/TC/DI Input Module
- Wiring the 4-Wire RTD Resistance Input Module
- Wiring the Strain Input Module
- Wiring the Pulse Input Module and Digital Input Module
- Wiring with the Analog Output Module
- Wiring with the PWM Output Module
- Wiring with the Digital Output Module
- 2.5 Connecting the Power Supply and Turning the Power Switch ON and OFF
- 2.6 Connecting the Ethernet Cable
- 2.7 Connecting the RS-422A/485 Interface (/C3 Option)
- 2.8 Connecting the RS-232 Interface (/C2 Option)
- 2.9 Measures Against Noise on the MW100 Data Acquisition Unit
- 2.10 Handling of the CF Card
- Chapter 3 Setting and Data acquisition
- 3.1 Connection Environment
- 3.2 Communication Settings
- 3.3 System Settings
- 3.4 Setting Acquisition Conditions for Measured/Computed Data
- 3.5 Setting Measurement Conditions (Measurement Channel Settings)
- 3.6 MATH Settings (MATH Channel Settings and the /M1 Option)
- 3.7 Setting Alarms
- 3.8 Digital Output Settings
- 3.9 Analog/PWM Output Settings
- 3.10 Event/Action Settings
- 3.11 Timer and Match Time Settings
- 3.12 Report Settings (/M3 Option)
- 3.13 Starting and Stopping Measurement, Computation, and Recording
- 3.14 Network Utility Settings
- 3.15 Saving and Loading Setup Data
- 3.16 Measured Data Monitor Display/Settings
- Chapter 4 Troubleshooting and Maintenance
- Chapter 5 Specification
- 5.1 Common Specifications
- 5.2 Main Module (MW100-E) Specifications
- Measurement
- MATH
- MATH Function Specifications (/M1 Option)
- RJC
- Remote RJC (RRJC)
- Alarms
- Report Function Specifications (/M3 Option)
- Recorder Structure
- Display
- Communication
- Modbus Protocol Specifications
- EtherNet/IP Server Function (Firmware version R3.02 or later)
- Event Action
- Timer and Match Time
- User Interface
- Other Functions
- General Specifications
- External Dimensions
- 5.3 Base Plate (MX150) Specifications
- 5.4 4-CH, High-Speed Universal Input Module (MX110-UNV-H04) Specifications
- 5.5 10-CH, Medium-Speed Universal Input Module (MX110-UNV-M10) Specifications
- 5.6 30-CH, Medium-Speed DCV/TC/DI Input Module (MX110-VTD-L30) Specifications
- 5.7 6-CH, Medium-Speed Four-Wire RTD Resistance Input Module (MX110-V4R-M06) Specifications
- 5.8 4-CH, Medium-Speed Strain Input Module (MX112) Specifications
- 5.9 10-CH, Pulse Input Module (MX114) Specifications
- 5.10 10-CH, High-Speed Digital Input Module (MX115) Specifications
- 5.11 8-CH, Medium-Speed Analog Output Module (MX120-VAO-M08) Specifications
- 5.12 8-CH, Medium-Speed PWM Output Module (MX120-PWM-M08) Specifications
- 5.13 Operations Common to the 8-CH Medium-Speed Analog Output Module and the 8-CH Medium Speed PWM Output Module (MX120)
- 5.14 10-CH, Medium-Speed Digital Output Module (MX125) Specifications
- Appendix
- Appendix 1 Supported Characters
- Appendix 2 Setting Data Communication That Uses Modbus Protocol
- Appendix 3 Using the Event Action
- Appendix 4 E-Mail Format
- Alarm Notification E-mail Format
- Report Notification E-mail Format (/M3 option)
- File Creation Notification E-mail Format
- Media Remaining Space Notification E-mail Format
- Power ON Notification E-mail Format
- System Error Notification E-mail Format
- Periodic Report Notification E-mail Format
- Test E-mail Format
- Appendix 5 Retrieving Files Using WebDAV
- Appendix 6 Network Terminology
- Appendix 7 Using the Broken Line Data of Decimal Values
- Appendix 8 Saving Data to the CF Card
- Index