Brocade Multi-Service IronWare Multiprotocol Label Switch (MPLS) Configuration Guide (Supporting R05.6.00) - Manual (Page 258)

Brocade# show mpls ted database
AreaId: 0
NodeID: 2.2.2.2, Type: Router
Type: M/A, To: 10.1.1.3, Local: 10.1.1.2, Remote: 0.0.0.0
NodeID: 3.3.3.3, Type: Router
Type: P2P, To: 10.6.6.6, Local: 10.1.1.1, Remote: 10.1.1.2
Type: M/A, To: 10.1.1.3, Local: 10.1.1.3, Remote: 0.0.0.0
Type: M/A, To: 10.1.1.2, Local: 10.1.1.1, Remote: 0.0.0.0
NodeID: 10.1.1.3, Type: Network
Type: M/A, To: 10.1.1.1, Local: 0.0.0.0, Remote: 0.0.0.0
Type: M/A, To: 10.2.2.2, Local: 0.0.0.0, Remote: 0.0.0.0
Type: M/A, To: 10.3.3.3, Local: 0.0.0.0, Remote: 0.0.0.0
NodeID: 30.1.1.2, Type: Network
Type: M/A, To: 10.1.1.1, Local: 0.0.0.0, Remote: 0.0.0.0
Type: M/A, To: 10.6.6.6, Local: 0.0.0.0, Remote: 0.0.0.0
234 Multi-Service IronWare Multiprotocol Label Switch (MPLS) Configuration Guide
53-1003031-02
Displaying the Traffic Engineering database
1
The following example is for a router where IS-IS TE LSPs are enabled for MPLS interfaces.
Brocade# show mpls ted database
This Router is XMR3
Global Link Gen 106
ISIS(2)
NodeID: XMR4.00(10.12.12.12) , Type: Router
Type: M/A, To: XMR3.02 Local: 10.0.0.1, Remote: 0.0.0.0, Gen 54
Type: M/A, To: XMR3.03 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 51
Type: M/A, To: PE2-JNPR.04 Local: 10.0.0.1, Remote: 0.0.0.0, Gen 57
Type: M/A, To: GSR.02 Local: 10.0.0.1, Remote: 0.0.0.0, Gen 78
NodeID: XMR3.00(10.15.15.15) , Type: Router
Type: M/A, To: XMR3.02 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 49
Type: M/A, To: XMR3.03 Local: 10.0.0.1, Remote: 0.0.0.0, Gen 50
NodeID: PE2-JNPR.00(10.5.5.5) , Type: Router
Type: M/A, To: PE2-JNPR.04 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 62
Type: M/A, To: PE2-JNPR.02 Local: 10.0.0.1, Remote: 0.0.0.0, Gen 60
Type: M/A, To: PE4.03 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 104
NodeID: GSR.00(10.9.9.9) , Type: Router
Type: P2P, To: PE4.00(10.14.14.14) Local: 10.0.0.2, Remote: 10.0.0.1, Gen 103
Type: M/A, To: GSR.02 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 65
Type: M/A, To: PE2-JNPR.02 Local: 10.0.0.2, Remote: 0.0.0.0, Gen 77
Syntax: show mpls ted database
The following table describes the output of the show mpls ted database command.
TABLE 18 Output from the show mpls ted data command
This field... Displays...
Global Link Gen The number of times the TED database has changed.
AreaId The ID of this OSPF area.
NodeID The ID of the node. For Router nodes, can be any interface address or a loopback interface
address on the LSR. For Network nodes, this is the router ID of the network’s designated router.
[node] Type The type of node. The node type can be either Router or Network
RouterIndicates the node is an actual LSR.
NetworkIndicates the node represents a multi-access network.